Data Loading...
Sagane™ Inter centralisé de volet 845 27 Flipbook PDF
Description 2 Médias de communication PLC => Courant porteur IR => Infrarouge Voyant LEARN N d'identification
130 Views
72 Downloads
FLIP PDF 604.73KB
Sagane™ Inter centralisé de volet 845 27
Caractéristiques
Tension Fréquence
100 - 240 V± 50 - 60 Hz 2 x 2,5 mm2
Profondeur = mini. 40 mm Norme
Courant porteur EN 50065 IEC 60669-2-1 - 5°C à + 45°C
Branchement
N L
A la première mise sous tension l’appui sur les touches Montée - Stop - Descente commande l’ensemble des points d’ouvrants (volet roulant ou store) de l’installation “In One by Legrand”. L’appui sur Learn(1) annule cette fonction de commande générale. (1) Touche de programmation ou apprentissage.
N0064FL3/ 02
Configuration d’usine
Description
Voyant LEARN
Médias de communication PLC => Courant porteur IR => Infrarouge
N d'identification
Cellule Infrarouge
Touches de commandes
Touche LEARN
Fonctionnement L’inter centralisé de volet peut commander simultanément à partir de ses touches Montée - Stop - Descente un ensemble de produits (acteurs) qui lui sont associés lors de l’apprentissage(1), il est alors Leader du scénario(2). L’inter centralisé de volet est toujours le point central de commande (Leader) d’un scénario. Il possède une interface pour les signaux infrarouges qui permet la commande de ses scénarios et /ou d’autres produits de l’installation. Il possède deux entrées auxiliaires E1 et E2 qui peuvent être reliés à un interrupteur horaire,... (privilégier les références 846 33 et 744 25) : - L’apparition de la tension sur E1 lance le scénario qui est enregistré sur la touche de commande Montée. - L’apparition de la tension sur E2 lance le scénario qui est enregistré sur la touche de commande Descente.
Attention : Privilégier un câblage inférieur à 5 mètres entre les entrées auxiliaires du produit (E1, E2) et l’interrupteur horaire. La touche de commande Stop n’est pas accessible à partir des entrées auxiliaires E1 et E2.
(1) Apprentissage : action d’associer des produits en vue de les commander simultanément à partir d’un point central. Cette association se réalise en appliquant la procédure d’apprentissage du scénario en page 3. (2) Scénario : correspond à l’ensemble des produits (acteurs) qui sont associés à une touche de commande.
2
Apprentissage du scénario Etape 1 : débuter l'apprentissage (sur le LEADER)
Appuyer sur LEARN
Appuyer sur la touche de commande qui doit piloter le scénario
Etape 2 : ajouter un acteur au scénario (sur l'ACTEUR)
Pour ajouter plusieurs produits au scénario,répéter pour chaque acteur les opérations et .
Appuyer sur la touche de commande qui doit être associé au leader
Appuyer sur LEARN Etape 3 : enregistrer le scénario (sur le LEADER)
Les voyants de tous les produits s'éteignent. Le scénario est enregistré. Appuyer sur LEARN
Modification d’un scénario Etape 1 : ouvrir le scénario (sur le LEADER)
Appuyer sur LEARN
Les voyants de tous les produits du scénario clignotent.
Appuyer sur la touche de commande qui pilote le scénario
Etape 2 : modifier l'état d'un acteur du scénario (sur l'ACTEUR)
Appuyer sur LEARN
ou
Appuyer sur LEARN
Appuyer sur la touche de commande que l'on souhaite associer
Pour supprimer le produit du scénario passer à l'étape 3 Etape 3 : enregistrer le scénario (sur le LEADER)
Les voyants de tous les produits s'éteignent. Le scénario est enregistré. Appuyer sur LEARN
Effacement d’un scénario Effacer tous les scénarios liés à la touche de commande (sur le LEADER)
Appuyer sur LEARN
Le scénario est effacé Appuyer sur la touche de commande et maintenir 10s
5s
Effacer tous les scénarios liés à ce produit (sur le LEADER)
Appuyer sur LEARN
Retour du produit en configuration usine Appuyer sur LEARN et maintenir 10s
5s
Légende Le voyant s'éteint
Le voyant clignote lentement
Le voyant clignote rapidement 3
Le voyant flashe
Sagane™ Centrale rolluikschakelaar 845 27
Eigenschappen
Spanning Frequentie
100 - 240 V±
Diepte = mini. 40 mm Norm
50 - 60 Hz 2 x 2,5 mm2
Draaggolf EN 50065 IEC 60669-2-1 - 5°C tot + 45°C
Aansluiting
N L
Standaardconfiguratie Bij de eerste inschakeling worden bij een druk op de toetsen Omhoog – Stop – Omlaag alle openingspunten (rolluik of jaloezie) van de installatie “In One by Legrand” bediend.
5
Beschrijving
Controlelampje LEARN
Communicatiemiddelen PLC => Draaggolf IR => Infrarood
Identificatienummer
Infraroodcel
Bedieningstoetsen
Toets LEARN
Werking De centrale rolluikschakelaar inter voor luiken kan tegelijkertijd met behulp van de toetsen Omhoog – Stop – Omlaag productverzamelingen (actoren) bedienen die hier aan toegevoegd zijn tijdens het aanleren(1), het is dan de Leider van het scenario(2). Opmerking: alleen de toets ON hoeft ingelezen te worden, de toets OFF wordt automatisch ingelezen. Hij bezit een interface voor infrarode signalen waarmee zijn scenario’s en/of andere producten van de installatie bediend kunnen worden. Hij bezit twee hulpingangen E1 en E2 die aan kunnen worden verbonden. (Gebruik referentienummers 846 33 en 744 25). - Door het verschijnen van spanning op E1 wordt het scenario gelanceerd dat op de bedieningstoets Omhoog geregistreerd is. - Door het verschijnen van spanning op E2 wordt het scenario gelanceerd dat op de bedieningstoets Omlaag geregistreerd is.
Let op : Gebruik een kabel korter dan 5 meter tussen de extra ingangen van het product (E1, E2) en de tijdschakelaar. De bedieningstoets Stop is niet toegankelijk vanuit de hulpingangen E1 en E2.
(1) Aanleren : actie van het associëren van producten met de bedoeling deze tegelijkertijd vanaf een centraal punt te bedienen. Dit associëren geschiedt door toepassing van de aanleerprocedure van het scenario op pagina 7. (2) Scenario: komt overeen met alle producten (actoren) die bij een bedieningstoets horen.
6
Aanleren van het scenario Stap 1: beginnen met aanleren (op de LEIDER)
Druk op LEARN
Druk op de bedieningstoets die het scenario bestuurt
Stap 2: voeg een actor toe aan het scenario (op de ACTOR)
Herhaal voor het toevoegen van meerdere producten aan het scenario voor iedere actor
Druk op de bedieningstoets die aan de leider moet zijn toegevoegd
Druk op LEARN
de handelingen en .
Stap 3: het scenario registreren (op de LEIDER)
De controlelampjes van alle producten gaan uit. Het scenario is geregistreerd. Druk op LEARN
Wijziging van een scenario Stap 1: het scenario openen (op de LEIDER)
Druk op LEARN
De controlelampjes van alle producten van het scenario knipperen.
Druk op de bedieningstoets die het scenario bestuurt
Stap 2: de staat van een actor van het scenario wijzigen (op de ACTOR)
Druk op LEARN
Druk op LEARN
Druk op de bedieningstoets die u toe wilt voegen
of Ga voor het wissen van het product uit het scenario naar stap 3 Stap 3: het scenario registreren (op de LEIDER)
De controlelampjes van alle producten gaan uit. Het scenario is geregistreerd Druk op LEARN
Wissen van een scenario Wis alle scenario's die verbonden zijn met de bedieningstoets (op de LEIDER)
Druk op LEARN
Het scenario is gewist
Druk op de 5s bedieningstoets en houd deze 10 s ingedrukt
Wis alle scenario's die bij dit product horen (op de LEIDER)
Druk op LEARN
Legende
Druk op LEARN en houd deze 10 s ingedrukt
5s
Het controlelampje gaat uit
Het controlelampje knippert langzaam
Het controlelampje knippert snel
Het controlelampje flitst
7
Terugkeer van het product naar de standaardconfiguratie
Sagane™ General shutter controller 845 27
Characteristics
Voltage Frequency
100 - 240 V±
Depth = 40 mm min. Standard
50 - 60 Hz 2 x 2,5 mm2
EN 50065 Power line carrier IEC 60669-2-1 - 5°C to + 45°C
Connection
N L
Factory configuration The first time it is switched on, pressing the Up - Stop - Down keys controls all opening points (roller shutters or awnings) in the “In One by Legrand” installation. Pressing Learn(1) cancels this general control function. (1) Programming or learn key.
9
Description
LEARN indicator lamp
Communication media PLC => Mains-borne signalling IR => Infrared
ID number
Infrared cell
Command keys
LEARN key
Operation The general shutter controller Using its Up - Stop - Down keys it can simultaneously control a set of products (actors) that have been associated with it during the learn phase(1). It is then the Leader of the scenario(2). The general shutter controller is always the central control point (Leader) of a scenario. It has two auxiliary inputs, E1 and E2, which can be connected to a time switch, etc (preferably use Cat. Nos 846 33 and 744 25) : - The appearance of voltage on E1 starts the scenario which is recorded on the Up control key. - The appearance of voltage on E2 starts the scenario which is recorded on the Down control key.
Caution : Preferably less than 5 meters of cabling between the product’s auxiliary inputs (E1, E2) and the time switch. The Stop control key cannot be accessed from auxiliary inputs E1 and E2.
(1) Learn phase: Operation to associate products so that they can be controlled simultaneously from a central point. This association is carried out by applying the learn scenario procedure on page 11. (2) Scenario: Corresponds to the set of products (actors) that are associated with a command key.
10
Learn scenario Step 1: Start the learn phase (on the LEADER)
Press LEARN
Press the command key that is to control the scenario
Step 2: Add an actor to the scenario (on the ACTOR)
To add a number of products to the scenario, repeat operations and for each actor.
Press the command key that is to be associated with the leader
Press LEARN
Step 3: Record the scenario (on the LEADER)
The indicator lamps of all the products go off. The scenario is recorded. Press LEARN
Modification of a scenario Step 1: Open the scenario (on the LEADER)
Press LEARN
The indicator lamps of all the products in the scenario blink.
Press the command key that controls the scenario
Step 2 : Modify the state of an actor in the scenario (on the ACTOR)
Press LEARN
Press LEARN
Press the command key that is to be associated
or To remove the product from the scenario, go to step 3 Step 3 : Record the scenario (on the LEADER)
The indicator lamps of all the products go off. The scenario is recorded. Press LEARN
Clearing a scenario Clear all the scenarios linked with the command key (on the LEADER)
Press LEARN
The scenario is cleared
Press the command key and hold it down for 10 s
5s
Clear all the scenarios linked to this product (on the LEADER)
Press LEARN
Return the product to factory configuration Press LEARN and hold down for 10 s
5s
Key The indicator lamp goes off
The indicator lamp blinks slowly
The indicator lamp blinks quickly 11
The indicator lamp flashes