Data Loading...

IDX User Guide Flipbook PDF

Want to reduce down-time... while airing up? Use TyreSense IDX—the fastest inflator on the market! Want to reduce down-t

114 Views
18 Downloads
FLIP PDF 5.48MB

IDX inflation and deflation system USER GUIDE

Purpose Congratulations on the purchase of the TyreSense IDX: inflation and deflation system by RIMEX! PREFACE This user guide outlines safe operating procedures for the TyreSense IDX: inflation and deflation system (TRS-IDX) which can be used with: • the TyreSense Internal Sensor (TRS-SENSOR-DIA) • the TyreSense Magmount (TRS-MAGMOUNT) • the TyreSense Wake-up Tool • the TyreSense Extended RF >[email protected] RIMEX Supply Ltd. assumes no responsibility for the accuracy of the information presented in this guide, which is subject to change without notice and should not be considered a commitment by RIMEX Supply Ltd. RIMEX Supply Ltd. assumes no responsibility for any error that may appear in this guide. The procedures in this guide must be performed by qualified personnel. TyreSense is a registered trademark of RIMEX Supply Ltd. All other trademarks are the property of their respective owners. Copyright RIMEX Supply Ltd. 2018. All rights reserved. ID 4 IDX USER GUIDEX USER GUIDE

1.0: IDX Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1: What is the TyreSense IDX: inflation and deflation system? . . . 6 1.2: What value does the IDX offer? . . . . . . . . . . . . . . . . . . . . 7 1.3: What are the features of the IDX? . . . . . . . . . . . . . . . . . . . 7 CONTENTS 1.4: IDX Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.4.1: IDX Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.4.2: Pneumatic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.0: IDX Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2.1: Setup Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2.2: Operation Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.0: IDX Control Box Operation . . . . . . . . . . . . . . . . . . . . . . . . 20 3.1: Powering up the IDX Control Box . . . . . . . . . . . . . . . . . . 20 3.2: IDX HOME Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 3.2.1: Preset HOME Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 21 3.2.2: Time Based HOME Screen . . . . . . . . . . . . . . . . . . . . . . 22 3.3: IDX Sensor ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 3.4: IDX Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.0: IDX Control Box Display Main Menu . . . . . . . . . . . . . . . . . . 28 4.1: User Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 4.1.1: Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 4.1.2: Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.2: Configuring Inflation/Deflation Presets . . . . . . . . . . . . . . 32 4.2.1: Turning a Presets Group ON and OFF . . . . . . . . . . . . . . . 33 4.2.2: Naming a Presets Group . . . . . . . . . . . . . . . . . . . . . . . 33 4.2.3: Configuring Presets . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.0: IDX Installation, Maintenance and Service . . . . . . . . . . . . . . 38 5.1: IDX Pneumatic Assembly Installation . . . . . . . . . . . . . . . 39 5.1.1: IDX Wake-up Tool Assembly Installation (optional) . . . . . . . 40 5.1.2: IDX Control Box Installation . . . . . . . . . . . . . . . . . . . . . 40 5.2: Maintenance and Service . . . . . . . . . . . . . . . . . . . . . . . 41 5.2.1: Visual Maintenance Check . . . . . . . . . . . . . . . . . . . . . . 41 5.2.2: Operational Maintenance Check . . . . . . . . . . . . . . . . . . 42 5.2.3: Filter Regulator and Wake-up tool Regulator Service . . . . . 44 5.2.4: Check Valve Service . . . . . . . . . . . . . . . . . . . . . . . . . . 45 5.2.5: Pressure Switch and Regulator Adjustments . . . . . . . . . . . 45 IDX USER GUIDEX USER GUIDE TYRESENSE.COM 5 ID

6.0: IDX Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.1: IDX Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 48 6.2: IDX Error Messages and Error Lamp . . . . . . . . . . . . . . . . 51 6.3: IDX Software Troubleshooting . . . . . . . . . . . . . . . . . . . . 55 6.4: IDX Hardware Troubleshooting . . . . . . . . . . . . . . . . . . . 56 7.0: IDX Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 7.1: Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . 60 CONTENTS 7.1.2: Physical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 61 8.0: IDX Schematics and Flow Diagrams . . . . . . . . . . . . . . . . . . . 64 8.1: IDX Power Connector Pin-out . . . . . . . . . . . . . . . . . . . . 64 8.2: IDX Pneumatic Connector Pin-out . . . . . . . . . . . . . . . . . 65 8.3: IDX External Relay Schematic . . . . . . . . . . . . . . . . . . . . 66 ID 6 IDX USER GUIDEX USER GUIDE

1.1: What is the TyreSense IDX: inflation and deflation system? . . . 6 1.2: What value does the IDX offer? . . . . . . . . . . . . . . . . . . . . 7 1.3: What are the features of the IDX? . . . . . . . . . . . . . . . . . . . 7 1.4: IDX Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1.4.1: IDX Control Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.4.2: Pneumatic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SECTION 1.0: IDX OVERVIEW IDX USER GUIDEX USER GUIDE ID TYRESENSE.COM

1.0: IDX Overview 1.1: What is the TyreSense IDX: inflation and deflation system? Figure 1. TyreSense IDX System (Control Box and Pneumatic Assembly). SECTION 1.0: IDX OVERVIEW The TyreSense IDX automated tire inflator and deflator system is an advancement stemming from developments in wheel sensor technology, which significantly reduces the downtime demanded by mechanical or manual airing up. The TyreSense IDX rapidly delivers uninterrupted air flow, governed by 1 precise and continuous data from the TyreSense wheel sensor . Accurate inflation and deflation can also be achieved on hot tires using TyreSense’s real-time cold-pressure calculation. The IDX provides automatic shut-off using presets and safety controls along with a time-based mode of operation. The IDX provides a separate control assembly, keeping personnel a safe distance from potential hazard zones when performing inflation or deflation. 1 A TyreSense wheel sensor is not required, but is recommended, for system operation. 8 IDX USER GUIDE

1.2: What value does the IDX offer? You can use the TyreSense IDX to: • Inflate and deflate tires to preset gauge and cold pressures . • Inflate and deflate tires for a preset time. • Manually inflate and deflate tires. • Inflate and deflate “hot” tires confidently to their recommended cold inflation pressure. • Inflate and deflate tires not equipped with TyreSense wheel SECTION 1.0: IDX OVERVIEW sensors . 2 • Program up to 32 unique preset groups, each with settings for cold inflation pressure, gauge pressure and time-based inflation. • Customize each preset group with their own unique name. • Improve productivity . 3 1.3: What are the features of the IDX? • Automatic LCD brightness for outside operation. • Maximum pressure of 175 PSI. • Stainless and brass pipe and fittings. • IP65X water and dirt ingress resistance. • Internal rechargeable Lithium-ion battery for battery backed operation. • 12VDC power input. • Pneumatically actuated ball-valves with air reservoir. • One-inch piping, valves, and fittings. • Mechanical safety ball-valves on both the COMPRESSOR input and TIRE output. • Automatic shutoff in the case of loss of power or error condition 2 For tires that are not equipped with TyreSense wheel sensors, automatic shutoff can only be achieved using a preset time. 3 Even though the TyreSense IDX is an automated system with safety mechanisms in place to abort operation, the operator must NEVER LEAVE IT OPERATING WITHOUT OVERSIGHT. You may perform other tasks while the IDX is in operation, but you must always be available to monitor and respond to the IDX. IDX USER GUIDE TYRESENSE.COM 9

• Relay control for external devices such as warning lights or sirens. • Horizontal or vertical mounting of the Pneumatic Assembly. • Internal filter regulator with automatic pulse drain to remove impurities in the air supplied by the compressor or tire. • Built-in TyreSense Sensor Tracker support. • Optional TyreSense Wake-up Tool. • Optional RF Repeater enhances RF performance. 1.4: IDX Components Figure 2. IDX Control Box. SECTION 1.0: IDX OVERVIEW Figure 3. IDX Pneumatic Assembly. 10 IDX USER GUIDE

1.4.1: IDX Control Box Figure 4. IDX Control Box side view. C D B SECTION 1.0: IDX OVERVIEW E F Description Function Toggle switch turns the system ON (І) and OFF (O). B Power Switch The internal battery will still charge when external power is provided and the system is OFF. Bolt to close and secure the cover of the C Cover Latch Bolt IDX Control Box. TNC connector for attaching the supplied D RF DATA Connector antenna assembly. Eight-pin Deutsch connector for E PNEUMATICS providing control signals to the air valves. Six-pin Deutsch connector for providing power, ground and relay connections. F PWR/AUX NOTE: The relay is normally open (N/O) and can be configured to close. Refer \"7.1: Electrical Specifications\" IDX USER GUIDE TYRESENSE.COM 11

Figure 5. IDX Control Box front view. E F B C Description Function RED solid or flashing LED lamp to notify the user that an error has occurred during B ERROR SECTION 1.0: IDX OVERVIEW operation and the current operation has been aborted. YELLOW LED lamp to notify the user C AIR ON that the system is currently deflating or inflating. 4.3” full-colour LCD screen. D LCD Display Capacitive touch screen. GREEN LED (Light Emitting Diode) power E Power Indicator indicator. Light sensor for automatic LCD F Light Sensor brightness. 12 IDX USER GUIDE

1.4.2: Pneumatic Assembly Figure 6. IDX Pneumatic Assembly. SECTION 1.0: IDX OVERVIEW Description Function Powder-coated 0.1-inch (2.5mm) B PNEUMATIC COVER aluminum cover. Powder-coated 3/16 inch (4.75mm) PNEUMATIC mild-steel frame. C ASSEMBLY FRAME The frame supports horizontal and vertical mounting with 10mm holes. IDX USER GUIDE TYRESENSE.COM 13

Figure 7. Pneumatic Assembly compressor side. B D C SECTION 1.0: IDX OVERVIEW Description Function One-inch stainless steel NPT female B COMPRESSOR fitting for connection to a compressor. Eight-pin Deutsch connector for C CONTROL BOX connection to the TyreSense IDX Control Box. 1/8 brass NPT female fitting for connection to the optional TyreSense D WAKE UP TOOL PORT Wake-up Tool. NOTE: This port should be plugged if not used. 14 IDX USER GUIDE

Figure 8. Pneumatic Assembly exhaust side. B C SECTION 1.0: IDX OVERVIEW Description Function One-inch stainless steel NPT female fitting B TIRE PORT for connection to a tire. One-inch stainless steel NPT female fitting for connection to an exhaust muffler. NOTE: This port should be plugged if not C EXHAUST PORT used. NOTE: A muffler must be attached for safe operation. IDX USER GUIDE TYRESENSE.COM 15

Figure 9. Pneumatic Assembly internal front view. C B D SECTION 1.0: IDX OVERVIEW H E G F 16 IDX USER GUIDE

Description Function B ON/OFF ACTUATOR Actuator to turn on/off ball-valve. One-inch ball valve for controlling air flow C ON/OFF BALL VALVE to and from the TIRE port. Three-way, two-position, one-inch ball INFLATE/DEFLATE valve to direct air-flow between the D BALL VALVE COMPRESSOR port and TIRE port, and TIRE port and EXHAUST port. Air reservoir to allow actuations of the SECTION 1.0: IDX OVERVIEW deflate/inflate and on/off ball-valves in the event of a loss of COMPRESSOR port air E AIR RESERVOIR pressure. Used to abort operation in a safe and controlled manner. Aluminum bowl for holding captured water and particulates from the filter SEMI-AUTO DRAIN pressure regulator. F REGULATOR BOWL Includes a semi-automatic pulse (spit) drain. Bowl will automatically “spit” fluid during solenoid actuations. Regulates and filters air between the COMPRESSOR port and the on/off and deflate/inflate solenoids and actuators. PRESSURE REGULATOR Filters out water and particulates from the G FILTER air. Prevents contaminating the solenoids, actuators, and wake up tool pressure regulator. Regulates pressure between the filter H PRESSURE REGULATOR pressure regulator and the wake up tool port. IDX USER GUIDE TYRESENSE.COM 17

Figure 10. Pneumatic Assembly internal back view. G F SECTION 1.0: IDX OVERVIEW D E C B I 18 IDX USER GUIDE

Description Function IDX Control Box input to determine B PRESSURE SWITCH sufficient pressure is present in the reservoir to actuate ball valves. Electrically controlled pneumatic solenoid DEFLATE/INFLATE to deflate/inflate actuator. C SOLENOID Controlled by the IDX Control Box. Default/No-Power setting is inflate. SOLENOID EXHAUST Exhaust ports for pneumatic actuation of SECTION 1.0: IDX OVERVIEW D PORTS the ball valves. DEFLATE/INFLATE E Actuator to turn deflate/inflate ball-valve. ACTUATOR F ON/OFF ACTUATOR Actuator to turn on/off ball-valve. One-inch stainless steel NPT female fitting G TIRE PORT for connection to a tire. One-inch ball valve for controlling air flow H ON/OFF BALL VALVE to and from the tire port. One-way valve to prevent air from flowing I ¼ INCH CHECK VALVE from the air reservoir to the COMPRESSOR port. IDX USER GUIDE TYRESENSE.COM 19

2.0: IDX Quick Start 2.1: Setup Procedures 1. CLOSE the COMPRESSOR and TIRE port ball valves. 2. Connect a tire to the TIRE port. 3. Turn ON the air compressor that is connected to the Compressor port. 4. Turn ON the IDX. 5. Wait for the IDX HOME screen to be displayed on the IDX Control Box. 6. OPEN the Compressor port manual ball valve. 7. Select a desired Preset group and Preset. 8. Enter the SENSOR ID for the tire to be inflated or deflated, or click the Override Sensor ID. Overriding the sensor ID is only available for time- based/manual Presets with tires that do not contain a functional TyreSense wheel sensor. SECTION 2.0: IDX QUICK START 9. Wait for the IDX status message to indicate “Ready”. 10. Click INFLATE or DEFLATE to start operation. 11. The operation will commence until the Preset is reached, is stopped by the user, or ended due to status condition. 2.2: Operation Tips Pressuring Trimming: due to the wheel sensor transmission frequency and the flow capability of the IDX, it is possible to overshoot intended Presets. If exact pressure values are desired, create a time-based/Manual Preset and use it to manually trim the pressure. Manual Operation: time-based/manual Presets allow for complete manual control of the inflation or deflation process. Preset Group Naming: strategically name Preset groups for the vehicle, position, or tire. This will allow quick navigation of the Preset groups. ID 20 IDX USER GUIDEX USER GUIDE

3.1: Powering up the IDX Control Box . . . . . . . . . . . . . . . . . . 20 3.2: IDX HOME Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 3.2.1: Preset Home Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 21 3.2.2: Time Based Home Screen . . . . . . . . . . . . . . . . . . . . . . . 22 3.3: IDX Sensor ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 3.4: IDX Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 SECTION 3.0: IDX CONTROL BOX OPERATION IDX USER GUIDEX USER GUIDE ID TYRESENSE.COM

3.0: IDX Control Box Operation 3.1: Powering up the IDX Control Box To turn on the IDX, toggle the power switch located on the side of the IDX Control Box to the ON (I) position. The green power LED in the upper left of the LCD should illuminate within 10 seconds of turning on the power switch. The TyreSense logo and splash screen will be displayed on the LCD, followed by the home screen. Once the home screen appears, open the COMPRESSOR port manual ball-valve. This action will clear the “NO INPUT PRESSURE” warning if it is displayed. The IDX is now ready for use. Refer \"2.1: Setup Procedures\". 3.2: IDX HOME Screen The HOME screen is the default screen for the IDX. It displays the most recent gauge pressure, calculated cold pressure, and temperature received from the selected TyreSense wheel sensor. In addition to the most recent wheel sensor data, the HOME screen either displays a single INFLATE or DEFLATE button with a group of presets (refer Figure 11) or the DEFLATE and INFLATE buttons for time based inflation/deflation (refer Figure 12). Figure 11. Preset HOME screen. Figure 12. Time based HOME screen. SECTION 3.0: IDX CONTROL BOX OPERATION 22 IDX USER GUIDE

3.2.1: Preset HOME Screen Figure 13. Preset INFLATE HOME screen. Preset value. Wheel sensor ID. Main menu. Preset #1. Preset #2 (selected). Preset #3. Preset group Most recent IDX status. Selected Preset group. SECTION 3.0: IDX CONTROL BOX OPERATION wheel sensor data. Button Enables you to Open a MENU screen with buttons for configuration options, user settings, Tools, and other diagnostic information. Presets for the selected group. • Presets can be GAUGE, COLD, MANUAL, or DISABLED. • A selected Preset will be highlighted in BLUE. • A disabled Preset button will be non-clickable and BLACK . Press this button to select a group of Presets. Selected Preset Name of the selected group of Presets. Group TyreSense wheel sensor ID installed in the tire to be inflated or deflated. Most recent tire data received from the TyreSense wheel Tire Data sensor. • If no data is available, three dash marks will be displayed (---). IDX USER GUIDE TYRESENSE.COM 23

Button Enables you to Gauge showing the preset value along with the most recent tire data received from the wheel sensor. • Gauge pressure presets will show the most recent gauge Pressure pressure along with the preset value in GREEN. Gauge • Calculated cold pressure presets will show the most recent calculated cold pressure along with the preset value in DARK BLUE. • The pressure gauge is not displayed with time presets. The deflation or inflation button is clicked to activate the desired process. • The button is disabled and non-clickable until the IDX status indicates READY. Table 1. Preset DEFLATE/INFLATE HOME screen buttons. 3.2.2: Time Based HOME Screen HOME screens that do not have a pressure gauge, display both INFLATE and DEFLATE buttons along with an option to Override Sensor ID. Refer Figure 14 below. Figure 14. HOME screen without pressure gauge. SECTION 3.0: IDX CONTROL BOX OPERATION The HOME screen without the pressure gauge is only provided for time-based presets. This is done because the IDX can’t determine if the user intends to inflate or deflate a tire. The sensor override check box allows the user to ignore sensor data. 24 IDX USER GUIDE

Button Enables you to This button is pressed to start the deflation operation. This button is pressed to start the inflation operation. Allows for inflation and deflation without data being received from the wheel sensor. This would be required when: • The tire is not equipped with a TyreSense wheel sensor • A sensor status condition that is prohibiting operation, such as low signal strength, no sensor data, or sensor error. Sensor ID Override should not be selected for tires equipped with a functional TyreSense wheel sensor because some automatic abort mechanisms may be SECTION 3.0: IDX CONTROL BOX OPERATION overridden. Table 2. HOME screen without pressure gauge. When deflation or inflation is in progress, the IDX prevents the user from pressing all buttons except the STOP button. Figure 15 shows an example of a gauge pressure preset deflation in progress. Figure 15. Example of a deflation in progress. IDX USER GUIDE TYRESENSE.COM 25

When a time preset inflation or deflation is in progress, the STOP button will display the time remaining before an Auto STOP will occur. Figure 16 shows an example of a time preset inflation in progress. Figure 16. Example of an inflation in progress. 3.3: IDX Sensor ID When the Sensor ID button is clicked the following screen will be displayed. Figure 17. Enter the ID of the wheel sensor. SECTION 3.0: IDX CONTROL BOX OPERATION The user can enter the ID of the wheel sensor and click OK. Clicking the INDUCE button will allow the IDX to listen for magnetically induced transmissions from the wheel sensor. Sensors can be induced by swiping a magnet on the button of the sensor or using the TyreSense Sensor Buddy. Once the induced transmission is received, the IDX will automatically load the ID of the sensor. If the wheel sensor in the tire is unknown, the Sensor Tracker utility in the Tools menu is helpful. 26 IDX USER GUIDE

3.4: IDX Presets Automatic inflation/deflation shutoff is determined by the selected preset. Presets can be configured for cold-pressure, gauge pressure, or time-based in nature. For cold pressure presets, inflation/deflation will automatically shut off when the calculated cold pressure received by the wheel sensor meets the preset value. Gauge pressure presets operate in the same manor as cold pressure presets except that they use gauge pressure rather than cold pressure. Time based presets automatically shut off inflation/deflation after the elapsed time reaches the preset value. Cold Pressure Presets Figure 18. HOME screen with a cold pressure preset selected. SECTION 3.0: IDX CONTROL BOX OPERATION  Figure 18 shows an example of the home screen with a cold pressure preset selected. Cold pressure preset buttons can be identified by the preset value with a snow flake underneath. When selected, the cold pressure preset value will be displayed on the pressure gauge in DARK BLUE with a snow flake below the gauge needle. IDX USER GUIDE TYRESENSE.COM 27

Time Presets Figure 19. HOME screen with a time preset selected. Figure 19 shows an example of the home screen with a time preset selected. The home screen with a time preset selected will show both the inflate and deflate buttons rather than a pressure gauge. Time preset buttons can be identified by the preset value followed by the “Min” suffix. Time presets allow for the overriding of the wheel sensor ID. ! Override Sensor ID should not be selected for tires equipped with a functional TyreSense wheel sensor because some automatic abort mechanisms may be overridden. IDX Status The IDX status displayed on the home screen informs the user of the status of the IDX. The IDX will only permit the user to SECTION 3.0: IDX CONTROL BOX OPERATION start deflation/inflation when the IDX status message indicates Ready. All other IDX status’ must be cleared before operation can commence. Refer “6.0: IDX Troubleshooting”, for a description of the IDX status messages. IDX USER GUIDEX USER GUIDE 28 ID

4.1: User Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 4.1.1: Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 4.1.2: Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.2: Configuring Inflation/Deflation Presets . . . . . . . . . . . . . . 32 4.2.1: Turning a Presets Group ON and OFF . . . . . . . . . . . . . . . 33 4.2.2: Naming a Presets Group . . . . . . . . . . . . . . . . . . . . . . . 33 4.2.3: Configuring Presets . . . . . . . . . . . . . . . . . . . . . . . . . . 34 SECTION 4.0: IDX CONTROL BOX DISPLAY MAIN MENU IDX USER GUIDEX USER GUIDE ID TYRESENSE.COM

4.0: IDX Control Box Display Main Menu The Main Menu of the IDX Control Box display provides the user the ability to configure Presets, set User Options, set system Settings, and provides Tools and diagnostics. Figure 20. IDX Main Menu screen. 4.1: User Options Figure 21. IDX User Options screen. • Automatic: when selected, the display brightness will be adjusted automatically based on the time of day. • Brightness: manually adjust the screen contrast by sliding the bar left and right. SECTION 4.0: IDX CONTROL BOX DISPLAY MAIN MENU • Display Timeout: use this button to choose a desired timeout option (10 minutes, 30 minutes, 1 hour, 4 hours and MAX). MAX is not recommended because the LCD screen is susceptible to burn. 30 IDX USER GUIDE

4.1.1: Settings Figure 22. IDX Settings screen. • Deflation: select either ENABLED or DISABLED. When DISABLED is selected, the deflation option for the system will not be available. The default setting is ENABLED. • Cold Pressure: To properly calculate the TyreSense cold pressure, the medium inside the tire needs to be identified. SECTION 4.0: IDX CONTROL BOX DISPLAY MAIN MENU Select between WET or DRY/N2 (nitrogen). Ensure the cold pressure setting is the same as the TyreSense Receiver Unit and TyreSense Client. • Inflation Shutoff: Select one of the following options: Gauge: The inflator will shut off when the wheel sensor transmits the preset pressure. Smart: The inflator will shut off based on an automated calculation that determines the correct pressure, if it occurs between sensor transmissions (which may be delayed, since the sensor transmits only every-one minute or two psi change). • Relay Output: The power connector has a pin for connecting a relay to control external items, such and lights and sirens. Choose from the following options: OFF: No external relay control. AIR ON: Relay turns on when the AIR ON light is illuminated. ERROR: Relay turns on when an error condition occurs during inflation. IDX USER GUIDE TYRESENSE.COM 31

4.1.2: Tools Figure 23. IDX Tools screen. • Sensor Tracker: this feature displays data for all the active and induced TyreSense wheel sensors within about 100m of your location. • Sensor Scan: enables you to manually scan a TyreSense wheel sensor. Once selected, the sensor scanning screen will appear. Hold a magnet on the bottom of the wheel sensor to induce it. The sensor scanning screen will display the results. Figure 24. IDX Diagnostics screen. • Diagnostics: Do not use GUI, System or Console Diagnostics without the assistance of a System Administrator or SECTION 4.0: IDX CONTROL BOX DISPLAY MAIN MENU TyreSense Technical Support. 32 IDX USER GUIDE

Figure 25. IDX Diagnostics screen settings. IDX: the Diagnostics screen allows the user to temporarily override functionality for diagnostics. The following settings override any automatic safety and operational checks. PLEASE USE WITH CARE. ERROR LAMP: toggles the ERROR Lamp. SECTION 4.0: IDX CONTROL BOX DISPLAY MAIN MENU AIR ON: toggles the AIR LAMP and On/Off ball valve actuator. INF / DEF: toggles the Inflate/Deflate ball valve actuator. Relay: toggles the external relay output. ON = closed and OFF = open. Pressure Switch: indicates the pressure switch state. Voltage: system voltage, NOT INPUT VOLTAGE. Once this screen is exited, or the system is powered down. Normal IDX operation will commence. IDX USER GUIDE TYRESENSE.COM 33

4.2: Configuring Inflation/Deflation Presets Figure 26. IDX MAIN MENU screen. 1. From the HOME screen, click on the MENU button. 2. On the MAIN MENU screen, click on the Presets button. Figure 27. IDX Presets groups. 3. On the Presets screen, click on one of the 32 preset groups to configure. Presets Groups that are displayed as DISABLED are disabled and will not be available for selection by the GROUP SELECT button on the HOME screen. 4. Once clicked, the Preset Group screen be displayed. SECTION 4.0: IDX CONTROL BOX DISPLAY MAIN MENU 34 IDX USER GUIDE

Figure 28. IDX Presets group screen. 4.2.1: Turning a Presets Group ON and OFF From the Presets group screen, click on the Presets group button to select ON or OFF. Presets groups that are turned off will not be available for selection by the GROUP SELECT button on the HOME screen. SECTION 4.0: IDX CONTROL BOX DISPLAY MAIN MENU 4.2.2: Naming a Presets Group Figure 29. Presets group name selection. 1. On the Presets group screen, click on the Name button. Presets group Name entry screen. IDX USER GUIDE TYRESENSE.COM 35

2. On the Presets group Name screen, enter the alphanumeric name for the Preset Group. The following default entry formats are available: • abc/123 (default): lowercase alpha followed by numeric entry (eg. cat 797). • 123/ABC (press abc/123 button once to access): numeric followed by uppercase alpha entry (eg.797 CAT). • ABC/abc (press abc/123 button twice to access): uppercase followed by lowercase alpha entry (eg. CAT cat). Pressing the