Data Loading...
Nut Splitters / Tube Flaring / Screw Extractors Flipbook PDF
TM Work Safely With Hand Tools - Wear Safety Goggles OOLS T Nut Splitters / Tube Flaring / &E Bending Screw Extracto
126 Views
107 Downloads
FLIP PDF 971.34KB
T
&E OOLS
QUICK FINDER INDEX SCREW & STUD EXTRACTORS, TUBE BENDERS FLARING TOOLS & NUT SPLITTERS
Nut Splitter Tools .................................................................................... Page No. 331 Screw & Bolt Extractors ...................................................................... Page No. 331 to 335
Nut Splitters / Tube Flaring / Bending Screw Extractors
Screw Extractors & Sets ........................................................... Internal Pipe Extractors ............................................................. Stud Remover & Setter Sets ..................................................... Stud Extractors & Sets...............................................................
Page No. 332 to 335 Page No. 335 Page No. 331, 334, 335 Page No. 331, 334, 335
Tube Bending & Flaring Tools ............................................................ Page No. 336 to 339 Tube Benders .............................................................................. Tube Expanders .......................................................................... Flaring Tools ................................................................................ Multi Stepped Punch ................................................................... Swaging Tools ............................................................................. Flaring Tool Accessories ............................................................
Page No. 338, 339 Page No. 336 Page No. 336, 337 Page No. 338 Page No. 338 Page No. 337
Additional New Stud Extractor Chucks
Impact Stud Extractor Chucks
Can be Used for Drilling & Tapping Threads with Impact Wrenches
Impact Stud Extractors are adjustable to fit studs according to their drive size from 1/64" to 1/2" (1mm to 13mm) Works with 1/4"Drive, 3/8"Drive and 1/2"Drive impact ratchets and wrenches. Can also be used as a drill chuck on power tools. Will effectively work on threaded, broken, rusted, stripped and smooth studs. Rotate the impact wrench counter clockwise to extract the stud, the self tightening action of the tool grips and extracts the stud. Release by turning the hex nut clockwise.
No.8544 1/4"Drive Impact Stud Extractor Capacity: 1/64" to 1/4"(1mm to 6mm)
Keyless hand impact operation
8544
8545
8546
1/4"Drive Length: 2"(50mm)
3/8"Drive Length: 3"(75mm)
1/2"Drive Length: 3"(75mm)
No.8545 3/8"Drive Impact Stud Extractor Capacity: 1/4" to 1/2"(6mm to 13mm)
Keyless hand impact operation
No.8546 1/2"Drive Impact Stud Extractor Capacity: 1/4" to 1/2"(6mm to 13mm)
Keyless hand impact operation
330
TM
Work Safely With Hand Tools - Wear Safety Goggles
T
&E OOLS
NUT SPLITTERS
No.8658 Hydraulic Nut Splitter Splits rusted hex nuts up to 7/8"(22mm) across the flats! Angle head design allows tool to be used in inaccessible areas. Does not damage the bolt threads. Maximum Capacity: 7/8"(22mm) Length: 8"(204mm)
No.8658-C Replacement Blade to suit #8658
No.8654 Angle Nut Splitter
This angled nut splitter with open end jaw is required when access to the nut from overhead is not possible. Maximum Capacity: 7/8"(22mm) Length: 6.3/4"(170mm) a
No.8655 Replacement Blade to suit #8654
1993 1994
Pneumatic Nut Splitting Tools
No.8650 Offset Nut Splitter
Ideal for removing seized locking clamps on tie rod adjuster sleeves, exhaust flange nuts & shock absorbers nuts, etc.
No.1993
6" Nut Splitting Tool
Opening: 5/16"(8mm) Shank Diameter: .401"Parker shank
No.1994
Length: 6"(150mm)
10" Nut Splitting Tool
Opening: 3/8"(10mm) Shank Diameter: .401"Parker shank
No.8652
Length: 10"(250mm)
Splits rusted hex nuts up to 7/8"(22mm) across the flats. Offset head design allows tool to be used in inaccessible areas. Forcing screw features a swivelling tip to prevent tool from slipping. Does not damage the bolt threads. Capacity: 7/8"(22mm) Length: 4"(100mm) a
No.8651 Replacement Blade to suit #8650
4Pc. Nut Splitter Set
Splits rusted hex nuts up to 1.1/16"(27mm) across the flats! Flat round head design allows tool to be used in inaccessible areas. Cutting blade and forcing screw tip have a ball joint drive to prevent binding under load. Does not damage the bolt thread. Lengths: 1: 3.3/8"(86mm), 2: 4"(100mm), 3: 5.1/8"(130mm), 4: 6.1/8"(156mm) Set Contains:
4 3
Available Separately
Part No. Description Part No. Description 8652-1 Splitter 3/8"- 1/2"(9 - 12mm) 8652-3 Splitter 5/8"- 7/8"(16 - 22mm) 8652-2 Splitter 1/2"- 5/8"(12 -16mm) 8652-4 Splitter 7/8"- 1.1/16"(22 - 27mm)
No.8665
2
1
2Pc. Heavy-Duty Nut Splitter Set
Grease ram hydraulic nut splitters that will split seized hex nuts from the smallest size up to 1.1/2"(38mm) across the flats without damage to bolt or stud thread. Six interchangeable anvils suit different size hexagon nuts. Set Contains:
No.8658
a
Hydraulic Nut Splitter With Three Anvils Capacity: 7/8"(22mm)
8658-C
Length: 8"(204mm)
Replacement Blade for #8658
No.8659
8659-C
B
Available Separately
A
Large Hydraulic Nut Splitter With Three Anvils Capacity: 1.1/2"(38mm)
Length: 7.1/2"(190mm)
Replacement Blade for #8659
No.YC2000
Hydraulic Nut Splitter
Features five different hardened splitter bodies and specially tempered replaceable blades with a 10 ton hydraulic ram. This tool is designed to split seized hex nuts from the smallest size up to 1.7/8"(48mm) across the flats without damage to bolt or stud thread. Ram Length: 10.5/16"(262mm) Set Contains:
YC2001 YC2002 YC2003 YC2004 YC2005 YC2006 YC2007 TM
Splitter 1" Bolt Cap Splitter 3/4" Bolt Cap Splitter 5/8" Bolt Cap Splitter 1/2" Bolt Cap Splitter 3/8" Bolt Cap Ram Attachment Bush Attachment
Available Separately
1" Replacement Blade YC2008 3/4" Replacement Blade YC2009 5/8" Replacement Blade YC2010 1/2" Replacement Blade YC2011 3/8" Replacement Blade YC2012 10 Ton Hydraulic Ram YC8000A YC8000A-R Repair Kit for YC8000A
Work Safely With Hand Tools - Wear Safety Goggles
331
T
&E OOLS
SCREW & BOLT EXTRACTORS
No.8949 10Pc. Wedge-Proof Screw Extractor Set Designed to remove broken fasteners without breaking or jamming. Will turn broken fasteners out while permitting the highest torque without expansion. Table lists screw size diameters for each extractor size. Made from C4150 alloy steel. All Extractor Lengths: 1.3/8"(35mm) Set Contains:
Part No. 8939 8940 8941 8942 8943 8944 8945 8946 8947 8948
Wedge-Proof Screw Extractors
Available Separately
Description Screw Size Dia. 1/8" (3mm) Wedge-Proof Extractor 3/16" (5mm) 5/32" (4mm) Wedge-Proof Extractor 1/4" (6 -7mm) 3/16" (5mm) Wedge-Proof Extractor 5/16" (8mm) 7/32" (5.5mm) Wedge-Proof Extractor 3/8" (10mm) 1/4" (6mm) Wedge-Proof Extractor 7/16" (11mm) 9/32" (7mm) Wedge-Proof Extractor 1/2" (13mm) 5/16" (8mm) Wedge-Proof Extractor 9/16" (14mm) 11/32" (9mm) Wedge-Proof Extractor 5/8" (16mm) 3/8" (10mm) Wedge-Proof Extractor 11/16"(17-18mm) 13/32"(11mm) Wedge-Proof Extractor 3/4" (19mm)
No.8950 5Pc. Square Type Screw Extractor Set Sharp undercut edges provide a solid grip on broken studs, set screws, pipe and Alemite fittings. These screw extractors do not expand the screw whilst turning and their tapered design ensures a positive grip when driven into the drilled out hole. Drill size is stamped on each extractor for ease of identification. Contains five extractors #8951 to #8955 to remove screws and bolts from 1/4" through 5/8" diameter. For individual sizes see table below listed in #8960.
No.8988 25Pc. Wedge-Proof Screw Extractor Set Designed to remove broken fasteners without breaking or jamming. Will turn broken fasteners out while permitting the highest torque without expansion. Made from C4150 alloy steel. Sizes: 1/8" to 7/8" in 1/32" Increments (3mm to 22mm in 0.8mm) All Extractor Lengths: 1.3/8"(35mm)
No.8960 9Pc. Square Type Screw Extractor Set
Sharp undercut edges provide a solid grip on broken studs, set screws pipe and Alemite fittings. These screw extractors do not expand the screw whilst turning and their tapered design ensures a positive grip when driven into the drilled out hole. Drill size is stamped on each extractor for ease of identification. Set Contains: (except #10 No.8961)
Part No. 8951 8952 8953 8954 8955 8956 8957 8958 8959 8961
332
Description #1 Screw Extractor #2 Screw Extractor #3 Screw Extractor #4 Screw Extractor #5 Screw Extractor #6 Screw Extractor #7 Screw Extractor #8 Screw Extractor #9 Screw Extractor #10 Screw Extractor TM
1
Drill Hole
2
Drive in Extractor
3
Turn out broken Stud
Available Separately
Suites Screw Size Dia. 1/4" - 5/16" (6 - 8mm) 3/8" (9 - 10mm) 7/16" (11 - 12mm) 1/2" - 9/16" (13 - 14mm) 5/8" (15 - 16mm) 11/16" - 3/4" (17 - 19mm) 13/16" - 15/16"(20 - 24mm) 1" - 1.3/16" (25 - 30mm) 1.1/4" - 1.3/8" (31 - 35mm) 1.5/16" - 2" (33 - 50mm)
Drill Size 1/8" 3/16" 15/64" 5/16" 3/8" 15/32" 9/16" 21/32" 13/16" 1.1/16"
Work Safely With Hand Tools - Wear Safety Goggles
T
&E OOLS
SCREW & BOLT EXTRACTORS No.8965 Screw Extractor / Drill & Guide Set For Extracting Broken Screws, Studs & Bolts: 5mm to 16mm Threads Designed to remove broken fasteners without breaking or jamming. Will turn broken fasteners out while permitting the highest torque without expansion. Made from C4150 alloy steel. Supplied in tough PVC case.
Instructions For Use:
1. Carefully locate drill and guide bushing and engage ground HSS drill bit. For sizes of 7mm and up, pre-drill. 2. Drive in the extractor pin (no deformation of drilled part) 3. Put on the extractor nut and unscrew using a wrench. 4. Use special guide bushes when drilling sunken or protruding broken screws.
8965
Chart For Using Screw Extractors For screws that are really seized up first spray with a solvent or heat up. Extractor pins are manufactured from high grade materials and should be kept straight and not heated. Pre-Drill Bolt Hex Drill Nut Extractor mm Size mm Size Pin Size Size mm Size Size M5 Wr. 10 3.2 Size 1 Size 1 M6 Wr. 10 3.2 Size 1 Size 1 3.2 M7 Wr. 11 4.8 Size 2 Size 2 3.2 M8 Wr. 11 4.8 Size 2 Size 2 4.8 M9 Wr. 13 6.4 Size 2 Size 3 4.8 M10 Wr. 13 6.4 Size 3 Size 3 4.8 M12 Wr. 14 8.0 Size 4 Size 4 6.4 M14 Wr. 17 8.7 Size 5 Size 5 6.4 M16 Wr. 17 8.7 Size 5 Size 5 Replacement Parts for #8965 Screw Extractor Set Part No. Description Part No. Description 8965-A 3.2mm(1/8”) HSS Drill 8965-N #9 Drilling Guide 8965-B 4.8mm(3/16”) HSS Drill 8965-O #10 Drilling Guide 8965-C 6.4mm(1/4”) HSS Drill 8965-P #1 Extractor Pin 8965-D 8.0mm(5/16”) HSS Drill 8965-Q #2 Extractor Pin 8965-E 8.7mm(11/32”)HSS Drill 8965-R #3 Extractor Pin 8965-F #1 Drilling Guide 8965-S #4 Extractor Pin 8965-G #2 Drilling Guide 8965-T #5 Extractor Pin 8965-H #3 Drilling Guide 8965-U #1 Extractor Nut 8965-I #4 Drilling Guide 8965-V #2 Extractor Nut 8965-J #5 Drilling Guide 8965-W #3 Extractor Nut 8965-K #6 Drilling Guide 8965-X #4 Extractor Nut 8965-L #7 Drilling Guide 8965-Y #5 Extractor Nut 8965-M #8 Drilling Guide 8965-Z Blow Mold Case
No.8972 5Pc. Threading Tap Extractor Set The five piece Threading Tap Extractor Set has hardened thin fingers that fit into the flutes of broken taps thus enabling you to wind out the broken section. The five different sizes cover all size threading taps from 1/16"(1.5mm) to 1/2"(13mm) Extractors are made from high grade alloy steel, heat treated to give the tensile strength needed to remove hardened threading taps. Supplied in vinyl pouch. Set Contains:
Part No. 8972-A 8972-B 8972-C 8972-D 8972-E TM
Description Tap Extractor Tap Extractor Tap Extractor Tap Extractor Tap Extractor
Available Separately
Working Size Range 1/16" - 1/8" (1.5mm - 3mm) 3/16" - 1/4" (4.5mm - 6.5mm) (7mm - 9.5mm) 9/32" - 3/8" 13/32" - 7/16" (10mm - 11mm) 7/16" - 1/2" (11mm - 13mm)
8972
Work Safely With Hand Tools - Wear Safety Goggles
333
T
&E OOLS
SCREW, BOLT & STUD EXTRACTORS
Straight Flute Type
No.8967 5Pc. Spriral Type Screw Extractor Set
No.8962 5Pc. Screw Extractor Set
Will Work on Left & Right Hand Threads
Sharp undercut edges provide a solid grip on broken studs, set screws, pipe and Alemite fittings. These screw extractors do not expand the screw whilst turning. Sizes: #1, #2, #3, #4, #5
This is a professional quality screw extractor. Made of hi-grade heat treated alloy steel. Quick and easy way to remove broken screws, pipes, bolts and studs. Sizes: #1, #2, #3, #4, #5
No.8913 6Pc. 3/8"Drive Impact Wedge Proof Extractor Set
New design 3/8"Drive impact type wedge proof extractors. Made from SNCM+V molybdenum steel with heat treatment to obtain maximum hardness without breaking. Contains sizes as per table. Individual Sizes:
Part No. 8913-2 8913-3 8913-4
Available Separately
Length 61mm 61mm 61mm
Size 2mm 3mm 4mm
Part No. 8913-6 8913-8 8913-10
Size 6mm 8mm 10mm
Length 61mm 61mm 61mm
Part No. 8529 8530 8531 8532 8533 8534 8535 8536
Available Separately
Collet Size Housing 1/4" x 20tpi 1/4" x 28tpi 5/16" x 18tpi 5/16" x 24tpi 3/8" x 16tpi 3/8" x 24tpi 7/16" x 14tpi
Part No. 8537 8538 8539 8540 8541 8542 8543
Collet Size 7/16" x 20tpi 1/2" x 13tpi 1/2" x 20tpi 9/16" x 12tpi 9/16" x 18tpi 5/8" x 11tpi 5/8" x 18tpi
Flush type cam style 1/2" square drive stud remover. The tighter the stud the more firmly the tool grips. Made from high grade, heat treated alloy steel. Capacity: 1/4" to 3/4"(6 to 19mm) a
8526-R
Replacement Knurled Roller
No.8914 5Pc. 1/2"Drive Impact Wedge Proof Extractor Set
New design 1/2"Drive impact type wedge proof extractors. Made from SNCM+V molybdenum steel with heat treatment to obtain maximum hardness without breaking. Contains sizes as per table. Individual Sizes:
Part No. Size 8 to 10mm 8914-8 8914-10 10 to 12mm 8914-12 12 to 14mm
No.8528 15Pc. Imperial Stud Remover / Setter Set Contains:
No.8526 Stud Remover
Available Separately
Length Part No. Size Length 81mm 8914-14 14 to 16mm 81mm 81mm 8914-16 16 to 18mm 81mm 81mm
Stud Removing & Setting Kits The best way to remove studs without causing damage to the shanks. The tapered collets thread onto the stud, even if only a few threads are exposed. Tightening the housing bolt draws the collet up into the tapered housing & securely clamps the collet onto the stud for easy stud removal or setting.
No.8552 15Pc. Metric Stud Remover / Setter Set Contains:
Available Separately
Part No. Collet Size Housing 8529 6 x 1.00mm 8553 7 x 1.00mm 8554 8 x 1.00mm 8555 8 x 1.25mm 8556 9 x 1.00mm 8557 9 x 1.25mm 8558 10 x 1.25mm 8559
334
TM
Part No. 8560 8561 8562 8563 8564 8565 8566
Collet Size 10 x 1.50mm 12 x 1.25mm 12 x 1.50mm 14 x 1.50mm 14 x 2.00mm 16 x 1.50mm 16 x 2.00mm
Work Safely With Hand Tools - Wear Safety Goggles
SCREW, PIPE & STUD EXTRACTORS
No.8970 Internal Pipe Extractor Set
No.8969 3Pc. Screw Extractor Set Three piece screw extractor set is made of High Speed Steel (HSS) with hardness of HRC63. They feature 60° angle cutting edge with centre point to drill left handed to remove broken screws. Individual Sizes:
Part No. 8969-1 8969-2 8969-3
Available Separately
Description Screw Extractor Screw Extractor Screw Extractor
T
&E OOLS
Sizes #1 (6 to 8mm) #2 (9 to 10mm) #3 (11 to 12mm)
Grips internally on pipe and tube fittings. Internal pipe wrenches eliminate damage to internal threads, walls and high polished pipe fittings. The extractors feature a knurled concentric cam action section that securely locks the extractors internally allowing pipe removal without damage to either internal or external surfaces. Set consists of six sizes with range of: 5 to 30mm. Note: Concentric can extend each extractors range. Individual Sizes:
Part No. 8970-A 8970-B 8970-C
Available Separately
Part No. Description Description Sizes Internal Extractor 5 to 6mm 8970-D Internal Extractor Internal Extractor 7 to 9mm 8970-E Internal Extractor Internal Extractor 10 to 13mm 8970-F Internal Extractor
Sizes 14 to 17mm 18 to 22mm 23 to 30mm
Roller Cam Stud Extractors
For removal or installation of studs. Simply put the socket over the stud, then just turn in either direction using a 3/8" drive or 1/2" drive ratchet or wrench. Roller cams grip firmly onto stud. Sets come complete in a blow mold cases.
No.5042 Metric Stud Remover Set
Set Contains: 6mm, 8mm, 10mm, 12mm
Stud Pullers 1/2"Drive
New Chrome Molybdenum Short Series Stud Pullers
New Chrome Molybdenum Short Series Stud Pullers
No.5043M Metric Stud Remover Set
No.5043A SAE Stud Remover Set
Contains: 6mm, 8mm Stud Pullers 3/8"Drive Contains: 1/4", 5/16" Stud Pullers 3/8"Drive 10mm, 12mm Stud Pullers 1/2"Drive 3/8", 7/16" Stud Pullers 1/2"Drive
No.5050 6Pc. SAE Roller Cam Stud Extractor Set Contains All 6 Sizes: 3/16" to 1/2" as per table below.
Set Contains:
Part No. 5051 5052 5053 5054 5055 5056 TM
Size 3/16" 1/4" 5/16" 3/8" 7/16" 1/2"
Available Separately
Description Cam Stud Extractor Cam Stud Extractor Cam Stud Extractor Cam Stud Extractor Cam Stud Extractor Cam Stud Extractor
Drive 3/8" 1/2" 1/2" 1/2" 1/2" 21mm Hex
Repair Kit No. 5051-R 5052-R 5053-R 5054-R 5055-R 5056-R
Repair Kit Repair Kit Repair Kit Repair Kit Repair Kit Repair Kit
No.5049 7Pc. Metric Roller Cam Stud Extractor Set
a
Contains All 7 Sizes: 5 to 14mm as per table below. Set Contains: Available Separately
Part No. Size 5035 5mm 5038 6mm 5037 7mm 5039 8mm 5040 10mm 5041 12mm 5045 14mm
Description Drive Repair Kit No. Cam Stud Extractor 3/8" 5035-R Repair Kit Cam Stud Extractor 1/2" 5038-R Repair Kit Cam Stud Extractor 1/2" 5037-R Repair Kit Cam Stud Extractor 1/2" 5039-R Repair Kit Cam Stud Extractor 1/2" 5040-R Repair Kit Cam Stud Extractor 1/2" 5041-R Repair Kit Cam Stud Extractor 21mm Hex 5045-R Repair Kit
Work Safely With Hand Tools - Wear Safety Goggles
335
T
&E OOLS
TUBE BENDING & FLARING TOOLS
No.CT808 Automatic Flaring Tool
Features an eccentric cone type flaring tool for a perfect smooth single flare. The high grade alloy steel swivel is heat treated, precision ground and has phosphate finish to reduce friction. The yoke is also drop forged & heat treated. Set includes a tube cutter and deburring tool. Sizes: 3/16", 1/4", 5/16", 3/8", 1/2", 5/8", 3/4"
No.7206
No.CT276 Three-In-One Flaring Tool
This set can do single flares, double flares & swaging flares. Supplied with double flare adaptors from 3/16" to 1/2", swaging flares adaptors 3/16" to 3/4" & deburring tool. Sizes: 3/16", 1/4", 5/16", 3/8", 1/2", 5/8", 3/4"
Professional Double Flaring Tool
Extra heavy duty vice action flaring tool, built for high production usage. Does both double & ball flares on steel, Bundy tubing, copper, etc. The 3/16" & 1/4" tapered holding dies securely hold the tubing & the alignment die sets the correct depth for the flare. The double ended 3/16" & 1/4" forming dies are then used to create the double or ball flare. Reverse the forming die to finish off the double or ball flare. Sizes: 3/16"(4.75mm) & 1/4"(6mm) Replacement Dies: A) #7206-F316 3/16" Forming Die B) #7206-F14 1/4" Forming Die C) #7206-FA 3/16"/1/4" Alignment Die D) #7206-316 3/16" Holding Die E) #7206-14 1/4" Holding Die
A
D
B E
C
Does both Double & Ball Flares
Anneal tube before use
Deburr tube inside & outside
Expand head until Suitable for equal diameter tubes stop is reached
No.7714
Tube Expander Set
For flaring, cutting and expanding annealed copper, aluminium, brass and mild steel tube. Expander Head Sizes: 3/8", 1/2", 5/8", 3/4", 7/8", 1" & 1.1/8" Outside Diameter. Each head has 6 guide channels to assure regular capillary flow. Includes #8026 Tube Cutter & #DT200 Male & Female Deburring Tool. Supplied in blow mold storage carrying case. Capacity: 1/8" to 1.1/8"(3 to 28mm) Size Range: 1/8" to 1.5/8"(3 to 40mm) Length: 15"(380mm)
336
TM
Deformed tubes can be restored
Guide notches assure capillary action
Work Safely With Hand Tools - Wear Safety Goggles
T
&E OOLS
TUBE BENDING & FLARING TOOLS
Used for Making Double Flares on Bundy Tubing on Brake Lines etc.
Used for Making Double Flares on Bundy Tubing on Brake Lines etc.
No.7203
Imperial Double Flaring Tool Set
This high quality double flaring tool is built to withstand the pressure necessary to double flare at 45° or ball form mild steel bundy tubing repeatedly. It will also produce a single flare. Set includes heavy-duty tube cutter. Adaptor Sizes: 3/16", 1/4", 5/16", 3/8" & 1/2"
No.7203-R No.7203BAR
Replacement Yoke for #7203 Replacement Bar for #7203
No.7203-S Imperial Double Flaring Adaptor Set Part No. 7203-A 7203-B 7203-C 7203-D 7203-E
Size 3/16" 1/4" 5/16" 3/8" 1/2"
Metric Double Flaring Tool Set
No.7204-R No.7204BAR
Replacement Yoke for #7204 Replacement Bar for #7204
No.7204-S Metric Double Flaring Adaptor Set
Set of seven adaptors #7204A thru to #7204G
Individual Sizes: Part No. Size Available Separately 7204-A 4.75mm 5mm 7204-B Description 6mm 7204-C Double Flare Adaptor 8mm 7204-D Double Flare Adaptor 10mm Double Flare Adaptor 7204-E 12mm Double Flare Adaptor 7204-F Double Flare Adaptor 14mm 7204-G
Set of five adaptors #7203A thru to #7203E Individual Sizes:
No.7204
This high quality double flaring tool is built to withstand the pressure necessary to double flare at 45° or ball form mild steel bundy tubing. It will also produce a single flare. Set includes heavy-duty tube cutter. Adaptor Sizes: 4mm, 4.75mm, 6mm, 8mm, 10mm, 12mm & 14mm
Available Separately Description Double Flare Adaptor Double Flare Adaptor Double Flare Adaptor Double Flare Adaptor Double Flare Adaptor Double Flare Adaptor Double Flare Adaptor
No.7208-S I.S.O. Double Flaring Adaptor Set Set of four adaptors #7208A thru to #7208D Individual Sizes:
Part No. Size 7208-A 4.75mm 6mm 7208-B 8mm 7208-C 7208-D 10mm
Available Separately
Description ISO Double Flare Adaptor ISO Double Flare Adaptor ISO Double Flare Adaptor ISO Double Flare Adaptor Chamfer Adaptor
Flaring Bar
Notches in Setting Bar Provide Correct Tube Depth for Double Flare
Tubing Swivel Adaptor
Flaring Bar Swivel
Flaring Bar
No.7208 I.S.O. Double Flaring Tool Set Front wheel drive cars and light trucks, both foreign and domestic, are installing the ISO sized steel brake lines with the ISO flare. This is not the standard double flare. The #7208 will accomplish the ISO flare without removing the brake line from the vehicle, and it has the strength to withstand the pressure necessary to flare mild steel tubing up to 1mm wall thickness used on front wheel drive brake lines. Adaptors: 4.75mm, 6.0mm, 8.0mm & 10.0mm TM
No.FT220 Deluxe Double Flaring Tool with 6-In-1 Adaptor This high quality 6 in 1 Double Flaring Tool is built to withstand the pressure necessary to double flare at 45° or ball form mild steel bundy tubing repeatedly. It will also produce a single flare. Features cam locking action on the six sided revolving collet head with double flare setting bar that gauges the correct depth of tube to be double flared. Sizes: 3/16", 1/4", 5/16", 3/8", 1/2" & 5/8"
No.FT220BAR
Replacement Bar for #FT220
Work Safely With Hand Tools - Wear Safety Goggles
337
T
&E OOLS
TUBE BENDING & CUTTING TOOLS
Tough All Metal Construction
No.8025 Midget Tube Cutter
No.DT200 Deburring Tool Male / Female
The ideal tool for cutting brake tubing etc. in close quarters. Cuts mild steel, copper, brass aluminium and plastics. Capacity: 1/8" to 7/8"(3 to 22mm) Length: 2.5/16"(58mm)
No.8025-C
Replacement Cutter for #8025 Tube Cutter
No.8026 Tube Cutter with Reamer This tubing cutter features rollers with a flare cut-off groove and an enclosed feed mechanism that will produce a smooth clean cut every time. The #8026 easily handles bundy tubing, steel, copper, brass, aluminium and plastic tubing. Tool comes complete with spare cutter and fold away deburring reamer. Capacity: 1/8" to 1.1/8"(3 to 28mm) Length: 4.3/4"(120mm)
No.8026-C
Replacement Cutter for #8026 Tube Cutter
No.FT301 Multi-Stepped Swaging Punch
Combination inside & outside deburring tool. Blades made from SAE-1086 steel. Size Range: 1/8" to 1.5/8"(3mm to 40mm) For non-ferrous metals. Length: 2"(50mm)
No.FT302 Multi-Stepped Wrench This multi stepped 1/2" male square drive wrench is used for radiator valve nipples, counter-threads and short tap extensions. Stepped design, hardened chrome plated CR-V steel for internal hexagon and double hexagon cam fittings and slotted nipples. Sizes: 3/8", 1/2", 3/4" & 1" As well as intermediate sizes. Length: 4.1/8"(105mm)
No.5474 HSS 12mm Countersink
This multi stepped flaring and swaging punch is ideal for air conditioning and refrigeration work on annealed mild steel, copper, brass and aluminium tubing. Sizes: 1/4", 5/16", 3/8", 1/2" & 5/8" Length: 6"(150mm)
For internal reaming of copper and mild steel pipes to remove burrs before flaring or double flaring is commenced. Made from high speed steel. Length: 4.3/4"(120mm)
Ratcheting Handle Permits Cutter To Rotate 360 Degrees
Ratcheting Handle Permits Cutter To Rotate 360 Degrees
No.TCR100 Standard Ratchet Type Tube Cutter
No.TCR110 Large Ratchet Type Tube Cutter
This ratchet action tube cutter is designed to cut tubes in confined areas, ideal for copper, brass and aluminium tubes. Supplied with spare blade in the handle. Size Range: 1/4" to 7/8"(6 to 22mm) Length: 6.3/8"(162mm)
This ratchet action tube cutter is designed to cut tubes in confined areas, ideal for copper, brass and aluminium tubes. Supplied with spare blade in the handle. Size Range: 5/16" to 1.1/8"(8 to 28mm) Length: 7.1/2"(190mm)
No.7710 Plier Type Tube Bender
Solid Steel Construction with Two Sizes on Each Former
Plier action tube bender makes tight bends without collapsing tubing. Roller adaptors included for each size & are locked into place with locating pin. Simply place tubing between adaptor & studs then squeeze handles to make the necessary bend. Sizes: 3/16", 1/4", 5/16", & 3/8"(5, 6, 8 & 10mm) Diameter Tube Length: 10"(255mm)
338
TM
Work Safely With Hand Tools - Wear Safety Goggles
TUBE BENDING & CHAMFERING TOOLS
T
&E OOLS
Length: 8.1/2"(217mm) Length: 5.3/4"(145mm)
No.8550 90° Precision Mini Tube Bender
l Ideal Tool for Automotive Brake Tube Bending
Three sizes in one, for accurately bending small diameter annealed copper, aluminium and thin wall steel tubing. Angle settings are marked on tool for accuracy of bend and repetitive bending capability. Strong durable die cast aluminium construction. Sizes: 1/8", 3/16" & 1/4" (3mm, 4mm, 6mm) Diameter Tube
No.7721 90° Precision Medium Tubing Bender Three sizes in one, for accurately bending small & medium diameter annealed copper, aluminium and thin wall steel tubing. Angle settings are marked on tool for accuracy of bend and repetitive bending capability. Strong durable die cast aluminium construction. Sizes: 1/4", 5/16", 3/8" ( 6mm, 8mm, 10mm) Diameter Tube
Length: 8.1/4"(210mm)
No.7709 Handy Tubing Bender Bends copper, steel, bundy tubing without kinking. Place tubing in correct groove size and turn handle to bend. Heavy-duty construction provides years of service at an economical price. Sizes: 3/16", 1/4", 5/16" & 3/8"(5 to 10mm) Diameter Tube
No.7711 Pipe Aid Tube Bending Pliers
Heavy-duty drop forged pliers designed specifically for tight bending of brake lines both 3/16" & 4.75mm diameter. Length: 9.1/2"(240mm)
No.7713 180° Precision Tube Bender This bender is capable of bending four different sizes of tube. For bending annealed copper, aluminium and thin wall steel to 180 degrees with a circle diameter of 2.1/2"(65mm). Simply spread long handles to 180 degrees, place tube in correct groove and pull handles to accurately bend to a determined angle. Angle settings are clearly marked on tool. Sizes: 3/16", 1/4", 5/16", 3/8" (5 to 10mm) Diameter Tube
Length: 12.1/2"(318mm)
Forward Bending
Reverse Bending
No.7724 Pipe Chamfering Tool Chamfers PVC and other PP and PE pipes to a 15° angle to match the angle of the joining socket, creating the correct angle for the joint to be glued correctly. Chamfering tool will adjust from 25mm to 168mm pipe outside diameters. Supplied with one replaceable spare cutting blade. Easy adjustment to the work piece with large control knobs. Size Range: 1" to 6.1/2"(25mm to 168mm) Pipes TM
No.7716
Master Tube Bender Set
One handed bender, bends beyond 90° on soft tube in copper, brass, aluminium and soft steel. Seven Die Formers: 1/4", 5/16", 3/8", 1/2", 5/8", 3/4", 7/8" O.D. (6mm, 8mm, 10mm, 13mm, 16mm, 19mm, 22mm O.D.) Includes bending guide arms and attachments for forward and reverse bending Includes: #8026 Tube Cutter Capacity: 1/8" to 1.1/8"(3 to 28mm) #DT200 Male & Female Deburrer Range: 1/8" to 1.5/8"(3 to 40mm)
Work Safely With Hand Tools - Wear Safety Goggles
339