Sliding Door Solutions Technical Installation Manual
Tekform Sliding Door Systems Glidesoft RD Bottom Running System Sliding Door System for Bottom Running Tracks
GlideSoft RD provides a floor to ceiling panel system for bottom running tracks. It is compatible with 4mm or 10mm panel, glass and acrylic with a 60kg load capacty per door. GlideSoft RD is available with or without the Titus SD100s damping system for smooth and silent soft closing.
GlideSoft TP Top Running System Sliding Door System for Top Running Tracks
2
GlideSoft TP provides a cabinet based panel system for top running tracks. It takes 16mm standard and 18mm routed panels with a 50kg load capacity per door. GlideSoft TP is available with and without soft close damping on side doors and offers a centre rest kit for centre doors.
www.titustekform.com.au
GlideSoft RD System Installation Instructions Installation of Top and Bottom Rail Top Rail
Bottom Rail
1. Cut the Top rail the inside length of the cabinet
3. Line up the rail so the front panel is in line with the front side of the end panel
2. Pre-drill pilot holes for screws alternately in the front and back rail grooves.
4. Screw into place.
1. Cut the Bottom rail the inside length of the cabinet
3. Position the rail so it is offset 8mm from the front side of the end panel
2, Pre-drill pilot holes into the profile
4. Screw into place.
3
GlideSoft RD System Installation Instructions Door Assembly U and Handle Extrusions 1. Referring to p.17, cut U profiles and handle profiles 2. Silicon inside the channel of the U profile and the side channel of the handle profile
Position the profiles onto the door, if the door is 4mm make sure the door is pushed to the front of the handle profile
Back view of door
4
www.titustekform.com.au
GlideSoft RD System Installation Instructions Door Assembly Wedge Gaskets
1. Referring to p.17, cut all wedge gaskets
2. Push the wedge gaskets into the remaining channel area of the aluminium profiles Note: Wedge gaskets are only used if you are using 4mm thick panel or glass.
Back view of door
Top Mechanism
1. Locate position of the top mechanism tight in the top corners,
3. Fix the mechanisms with screws 4. Repeat for the other side
2. Pre-drill into the aluminium profiles
Back view of door
5
GlideSoft RD System Installation Instructions Door Assembly Brushstrips
1. Cut Brush strips to length of the handle extrusion
3. The 6mm brush strips are located on all the side of every handle profile.
2. The 9mm brush strip is located on the back of the front door. It is positioned in the thin channel of the handle profile. It is to be on the handle profile which will be positioned in the middle when both doors are shut.
Back view of door
Bottom Mechanism
1. Locate position of the Bottom 3. Fix the mechanisms with screws mechanism tight in the bottom corners, 4. Repeat for the other side 2. Pre-drill into the aluminium profiles
Back view of door
6
www.titustekform.com.au
GlideSoft RD System Installation Instructions Door Assembly Soft Close Damping 1. Locate the lifters into the soft close mechanism
2. Locate the lifters and soft close to the top U profile, measuring 105mm on the side of closing from the outside of the handle profile to the edge of the soft close flat plate
3. Predrill holes into the U profile
4. Screw in with screwdriver
5. Fix with power drill
7
GlideSoft RD System Installation Instructions Actuator Installation Actuator Assembly
1. Locate actuator so the extended hole is over the groove line
3.. Drill hole and fix screw Note: Actuator can be adjusted after in second hole assembly. For adjustment instructions, see p.11
8
www.titustekform.com.au
2. Drill hole and fix screw
Tekform Sliding Door Systems Cabinet Formation GlideSoft RD Sliding Door System for Bottom Running Tracks
Mechanism location for top and bottom rails.
9
GlideSoft RD System Installation Instructions Table for Door Sizing 2 Door
Cabinet Overall Door
Height
A
C = A=55
Width
B
D = (B+30)/2
3 Door
Cabinet Overall Door
Height
K
M = K-55
Width
L
N = (L+45)/3
4 Door
Cabinet Overall Door
Height
U
W = U-55
Width
V
X = (V+60)/4
U Extrusion
Handle Extrusion
Vertical Wedge Gasket
F=C
G = C-35
Handle Extrusion
Vertical Wedge Gasket
P=M
Q = M-35
H = E-10
J = D-46
Horizontal Wedge Gasket
Door Panel S = M-3
O = N-68 U Extrusion
Door Panel I = C-3
E = J-68 U Extrusion
Horizontal Wedge Gasket
Handle Extrusion
Vertical Wedge Gasket
Z=W
AA = (W-35)
R = N-10
T = N-46
Horizontal Wedge Gasket
Door Panel
CC = W-3
Y = N-68
BB = X-10
DD = X-46
2 Door Installation
3 Door Installation
4 Door Installation
A
cabinet height
K
cabinet height
U
cabinet height
B
cabinet width
L
cabinet width
V
cabinet width
C
overall door height
M
overall door height
W
overall door height
D
overall door width
N
overall door width
X
overall door width
E
U extrusion width
O
U extrusion width
Y
U extrusion width
F
handle extrusion height
P
handle extrusion height
Z
handle extrusion height
G
vertical wedge gasket length
Q
vertical wedge gasket length
AA
vertical wedge gasket length
H
horizontal wedge gasket length
R
horizontal wedge gasket length
BB
horizontal wedge gasket length
I
door panel height
S
door panel height
CC
door panel height
J
door panel width
T
door panel width
DD
door panel width
10
www.titustekform.com.au
GlideSoft RD System Installation Instructions Adjusting the Mechanism Bottom Adjustment
1. Use a screwdriver and spanner to adjust the screw and bolt to make the mechanism sit higher or lower
Back view of door - inside cabinet
Actuator Adjustment
1. Remove second screw then rotate actuator to acheive desired soft close
Note: Bottom adjustment is only required when the door is not parallel.
Range of height with adjustable damper
2. Once you have found the optimal soft close, drill and fix screw Note: Actuator can be adjusted later if needed.
11
GlideSoft TP System Installation Instructions Installation of Top and Bottom Rail Top Rail
1. Referring to p.18, use CI measurement to cut top rail
3. Pre-drill holes every 300mm then fix with screws
2. Referring to p.17, set the profile in place
Bottom Rail
1. Referring to p.18, use CI measurements to cut the top rail 2. Referring to p.17, set the bottom of the profile in place
12
www.titustekform.com.au
3. Pre-drill holes every 300mm then fix with screws
GlideSoft TP System Installation Instructions Door Assembly Handle Extrusions 1. Referring to p.17-18 for sizing, cut door panels 2. Cut the handle extrusions the same height as the door panel Front view of door 3. Fit the handle profile to the door
Front view of door
4. Pre-drill holes into the handle extrusion, then fix screws so the handle extrusion is secure to the door
Back view of door
Back view of door
Front view of door
13
GlideSoft TP System Installation Instructions Front Door Assembly Top Mechanism
1. Using below measurement (45mm from centre of top hole to top of door), fix the top mechanisms to the top of the door
Actuator side
Bottom Locator
Actuator side
14
Actuator side
1. Using p.17 as a guide, fix the locators to the bottom of the door
Back view of door
www.titustekform.com.au
2. Fix actuator to the side of the door requiring damping, as shown below
Back view of door
2. Fix locators 70mm from each side of the door
GlideSoft TP System Installation Instructions Back Door Assembly Top Mechanism
Actuator side
Bottom Locator
1. Using below measurement (60mm from centre of top hole to top of door), fix the top mechanisms to the top of the door, making sure wheels align as seen on p.17
Actuator side
2. Fix actuator to the side of door requiring damping, as shown below
Back view of door
1. Using p.17 as a guide, fix the locators to the bottom of the door
Back view of door
2. Fix locators 70mm from each side of the door
Back view of door
15
GlideSoft TP System Installation Instructions Door Assembly Soft Close Damping
1. Locate the soft close block and and soft close in the front of the corner of the wardrobe, behind the top profile and tight to the side of the cabinet
2. Screw in place
Locations of top mechanisms and locators.
16
www.titustekform.com.au
Tekform Sliding Door Systems Cabinet Formation GlideSoft TP Sliding Door System for Top Running Tracks
Diagrams for cabinet and door measurements.
17
Tekform Sliding Door Systems Cabinet Formation GlideSoft TP Sliding Door System for Top Running Tracks
Diagrams for cabinet and door measurements.
Denotes locks in mechanisms for stability and security of doors.
Back door mechanism
18
www.titustekform.com.au
Front door mechanism
Worldwide design, manufacturing and local distribution capabilities
Australia Victoria
New South Wales
Queensland
Titus Tekform Pty Ltd 8/59 Jersey Road Bayswater, VIC, 3153 T: +61 3 9737 5566 Fax: +61 3 9729 8780
Titus Tekform Pty Ltd 83 Jedda Road Prestons, NSW, 2170 T: +61 2 9826 0007 Fax: +61 2 9826 0074
Titus Tekform Pty Ltd 76 Northlink Place Virginia, QLD, 4014 T: +61 7 3266 3999 Fax: +61 7 3266 5234
Titus Tekform Pty Ltd 2/24 Kane Road Wodonga, VIC, 3690 T: +61 2 6056 3188 Fax: +61 2 6056 3190
Titus Tekform Pty Ltd Unit 3, 100 Munibung Road Cardiff, NSW, 2285 T: +61 2 4954 4011 Fax: +61 2 4354 4233
Titus Tekform Pty Ltd 20 Civil Road Garbutt, QLD, 4814 T: +61 7 4779 1366 Fax: +61 7 4779 1316
Western Australia
Titus Tekform Pty Ltd (John Kaye Kitchen & Cabinet Hardware) Cnr Heffernan & Brookes Street Mitchell, ACT, 2911 T: +61 2 9826 0007 Fax: +61 2 9826 0074
New Zealand
Titus Tekform Pty Ltd (Biemel’s Cabinet Hardware) 5/2 Wittenberg Drive Canning Vale, WA, 6155 T: +61 8 9455 2122 Fax: +61 8 9455 3680
South Australia Titus Tekform Pty Ltd PO Box 357, Bayswater, VIC, 3153 T: +61 8 8447 3700 Fax: +61 8 8447 3183
Tasmania Titus Tekform Pty Ltd 88 Hopkins Street Moonah, TAS, 7009 T: +61 3 6273 1199 Fax: +61 3 6273 0050
Stefano Orlati Pty Ltd 34 Waipareira Avenue Henderson, Auckland, 0610 T: +64 9 837 0886 Fax: +64 837 8003 Stefano Orlati Pty Ltd 162 Wordsworth Street Sydenham, Christchurch, 8023 T: +64 3 981 8518 Fax: +64 3 942 7296
19
Titus Tekform Australia
Stefano Orlati New Zealand
www.titustekform.com.au
www.stefano-orlati.com
[email protected]
[email protected]
1300-0-TITUS
Connect with us LinkedIn.com/company/titustekform Instagram.com/titustekform Pinterest.com/titustekform "Titus Tekform"