Data Loading...
TOOL MAINTENANCE & REPAIR INFORMATION Flipbook PDF
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656 3 - 1 Always use Rivet Busters with in-line
118 Views
45 Downloads
FLIP PDF 477.54KB
AMERICAN PNEUMATIC TOOL
RIVET BUSTERS TOOL MAINTENANCE & REPAIR INFORMATION Always use Rivet Busters with in-line oilers. FIELD OPERATION Before: 1. Check to ensure you are using air tool oil or a 10W grade equivalent. 2. For screw on type handle, tighten handle to 200 ft. lbs. 3. For 4-Bolt type handle ensure all bolts are tight. 4. Check retainer, lock spring, upper sleeve and lower square retainer. Rubber bumper should be in good condition. 5. Clean any water and/or dirt from air hose before connecting it to the tool. During: 1. For your safety and that of others, keep tool against work at all times! 2. When moving from one work area to another, always shut tool off. 3. Do not use tool as a wedge or prying instrument. 4. When changing tool bit always shut air supply off and disconnect hose. 5. Check and refill oil reservoir in the line oiler as needed 6. Make sure handle is kept tight.
TROUBLE SHOOTING GUIDE If tool only blows air or flutters: 1. Check to see if piston shows signs of wear, if worn replace with new one. 2. Check valve system for signs of wear. In most cases, when worn, only the inner sleeve needs to be replaced. 3. Disassemble and check air ports for blockage. 4. On 4-Bolt Handle Rivet Buster, check flapper valve for wear. If worn, flip it over and use other side. If tool will not shut off: 1. Immediately turn off air source, then disconnect air supply. 2. Check throttle valve bushing for damaged o’rings. 3. Check teflon throttle valve for signs of wear. If worn, replace with new one.
After: 1. Flush tool with cleaning solvent, then refill with Air Tool oil or 10W grade equivalent. 2. For screw on type handle, tighten handle to 200 ft. lbs 3. For 4-Bolt type handle ensure all bolts are tight. 4. Do not leave tool in water or dirt. 5. Store the tool well oiled.
REMEMBER: PREVENTIVE MAINTENANCE WILL ASSURE MAXIMUM PERFORMANCE FROM ALL OF YOUR APT TOOLS.
APT
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
3-1
AMERICAN PNEUMATIC TOOL
MODEL 133 RIVET BUSTER
The APT Model 133 Rivet Buster, or Jumbo Rivet Buster as it is known, was originally designed to cut rivets off metal structures. The APT Rivet Buster is widely known now as a tough, powerful tool, with the ability to perform medium to heavy demolition work. At half the weight of the 60 lb. class paving breakers, the ratio of its high impact energy versus its weight makes the Rivet Buster Series the most efficient tools APT makes. The model 133 meets the weight requirements for bridge deck repair work. Rivet Busters are also popular for cutting up underground tanks.
SPECIFICATIONS Part Number
Bore
Stroke
BPM
CFM @ 90 PSI
Weight
Length
lbs.
inches
Air Inlet NPT
30
22-1/2
3/8 Female
inlet pressure
5216
1-3/16
8
1140
42-46
FEATURES 8" stroke ■ Drop forged D-style handle ■ Inside trigger for better 1/2" NPT control and safety ■ Deep case-hardened alloy steel cylinder 3486 1/2" ■ Uses jumbo extra heavy INLET HOSE BARB SWIVEL duty tool steel ■ Heavy duty upper and lower sleeves 1/2" NPT ■ Adjustable exhaust deflector 3389 3/8" NPT INLET ■ Teflon throttle valve SWIVEL ■
APT
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
3-3
AMERICAN PNEUMATIC TOOL 7531 HANDLE KIT (SEE DETAIL BELOW)
APT MODEL 133 RIVET BUSTER
3161 SPRING
PART NO. 5216
3160 VALVE ASSY
3156 REAR VALVE
3157 VALVE
16592 PIN
3158 FRONT VALVE
3165 PISTON
3152 CYLNDER
2994 SPRING
3162 RING 3163 DEFLECTOR 7531 HANDLE KIT
4374 SLEEVE
4491 BUSHING
3171 RETAINER
* 3155 GRIP
3147 LEVER
3170 BUMPER 5734 HOUSING
1269 O-RING 7079 RETAINER CAP 1158 RETAINING RING
3-4
3146 PIN
285 BUSHING
3151 VALVE
215 SPRING
APT
3153 GRIP ASSY
1269 O-RING
* 8573 BUSHING
8574 BUSHINHG ASSY
3150 PIN
REFERENCE ONLY * FOR (THESE PARTS NOT SOLD SEPARATELY)
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
9949 Tabor Place, Santa Fe Springs, California, CA 90670, U.S.A.
MODEL 633 RIVET BUSTER
The APT Model 633 Rivet Buster measures only 20 5/8” in length, delivering more power to those tight spaces. Weighing just 28 lbs, it’s perfect for limited access work or when ever a compact, light weight and powerful tool fits the bill. This tool features an innovative cylinder design that reduces overall weight without compromising tool strength or hitting force. SPECIFICATIONS Part # Bore Diameter (inches) Stroke (inches) Blows per Minute CFM @ 90 psi Weight (lbs) Length (inches) Air Inlet Size
18341 1 3/16” 6” 1100 42 to 46 28 20 5/8” ½” NPT Female
FEATURES • 6” Stroke • Drop forged, D-style handle • Inside trigger for better control and safety • Deep case hardened alloy steel cylinder • Uses jumbo extra heavy steel • Heavy duty upper and lower sleeves • Adjustable exhaust deflector • Teflon throttle valve
For assistance in any sales, technical, maintenance or repair questions, please call APT @ Phone 800 532 7402 or 562 204 1555 Fax 800 715 6502 or 562 204 1773 e-mail [email protected]
TDS-1044 Rev A
9949 Tabor Place, Santa Fe Springs, California, CA 90670, U.S.A. 7531 HANDLE ASSY 3161 SPRING
APT MODEL 633 RIVET BUSTER Part # 18341
3160 VALVE ASSY
3156 REAR VALVE 3157 VALVE
16592 PIN
3158 FRONT VALVE
18339 PISTON
18337 CYLINDER
2994 SPRING
3162 RING 7531 HANDLE ASSY
3163 DEFLECTOR
4491 BUSHING 3153 GRIP * 3155 ASSY HANDLE
4374 SLEEVE 3171 RETAINER
3147 LEVER
3146 PIN
3170 BUMPER 5734 HOUSING
18651 BUSHING
3151 VALVE 215 SPRING 1269 O RING 7079 RETAINER CAP
1269 O RING *8573 BUSHING
8574 BUSHING ASSY
3150 PIN
1158 RETAINING RING * NOT SOLD SEPARATELY
For assistance in any sales, technical, maintenance or repair questions, please call APT @ Phone 800 532 7402 or 562 204 1555 Fax 800 715 6502 or 562 204 1773 e-mail [email protected]
TDS-1045 Rev A
AMERICAN PNEUMATIC TOOL
MODEL 1133 RIVET BUSTER
The APT Model 1133 Rivet Buster is a jumbo Rivet Buster with an 11" stroke. This new model complements the “classic” 133 Rivet Buster in those applications where heavy demolition force is required. This model is widely known as a tough, powerful tool, with the ability to perform heavy demolition work. Rivet Busters are also popular for cutting up underground tanks.
SPECIFICATIONS Part Number
Bore
17399
1-3/16
Stroke
BPM
CFM @ 90 PSI
Weight
Length
lbs.
inches
Air Inlet NPT
33
25-1/2
3/8 Female
inlet pressure
11
850
48-52
FEATURES 11" stroke ■ Drop forged D-style handle ■ Inside trigger for better control and safety ■ Deep case-hardened alloy steel cylinder ■ Uses jumbo extra heavy duty tool steel ■ Heavy duty upper and lower sleeves ■ Adjustable exhaust deflector ■ Teflon throttle valve ■
1/2" NPT
1/2" HOSE BARB
3486 INLET SWIVEL
1/2" NPT
3/8" NPT
3389 INLET SWIVEL
APT
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
3 -5
AMERICAN PNEUMATIC TOOL 7531 HANDLE KIT (SEE DETAIL BELOW)
APT MODEL 1133 RIVET BUSTER
3161 SPRING
PART NO. 17399
3160 VALVE ASSY
3156 REAR VALVE
3157 VALVE
16592 PIN
3158 FRONT VALVE
17529 PISTON
17398 CYLNDER
2994 SPRING
3162 RING 3163 DEFLECTOR 7531 HANDLE KIT
4374 SLEEVE
4491 BUSHING
3171 RETAINER
* 3155 GRIP
3147 LEVER
3170 BUMPER 5734 HOUSING
1269 O-RING 7079 RETAINER CAP 1158 RETAINING RING
3 -6
3146 PIN
285 BUSHING
3151 VALVE
215 SPRING
APT
3153 GRIP ASSY
1269 O-RING
* 8573 BUSHING
8574 BUSHING ASSY
3150 PIN
REFERENCE ONLY * FOR (THESE PARTS NOT SOLD SEPARATELY)
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
AMERICAN PNEUMATIC TOOL
MODEL 133ST 1133ST RIVET BUSTER
The APT Model 133ST/1133ST Rivet Buster is available with an 8” or 11" stroke. This new model features a dual action safety trigger. This model is widely known as a tough, powerful tool, with the ability to perform heavy demolition work. Rivet Busters are also popular for cutting up underground tanks.
SPECIFICATIONS Part Number
Bore
Stroke
BPM
18070
1-3/16
8
1140
18082
1-3/16
11
850
CFM @ 90 PSI
Weight
Length
lbs.
inches
Air Inlet NPT
42-46
30
22-1/2
3/8 Female
48-52
33
25-1/2
3/8 Female
inlet pressure
FEATURES Safety trigger ■ 8" or 11" stroke ■ Drop forged open-style handle ■ Deep case-hardened alloy steel cylinder ■ Uses jumbo extra heavy duty tool steel ■ Heavy duty upper and lower sleeves ■ Adjustable exhaust deflector ■
1/2" NPT
1/2" HOSE BARB
3486 INLET SWIVEL
1/2" NPT
3/8" NPT
3389 INLET SWIVEL
APT
rev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
3-7
AMERICAN PNEUMATIC TOOL
18071 HANDLE KIT (SEE DETAIL BELOW)
APT MODEL 133-ST/1133-ST RIVET BUSTER
3161 SPRING
PART NO. 18070 (8" STROKE) PART NO. 18082 (11" STROKE)
3160 VALVE ASSY
3156 REAR VALVE
3157 VALVE
16592 PIN
3158 FRONT VALVE
3165 (8") 17529 (11") PISTON
3152 (8") 17398 (11") CYLINDER
2994 SPRING
18076 TRIGGER
3162 RING
18074 SPRING
3163 DEFLECTOR 4374 SLEEVE 3171 RETAINER
18080 PIN
18071 HANDLE KIT
18073 SAFETY TRIGGER ASSY
18076 SWIVEL
18072 HANDLE
1554 PIN
3170 BUMPER
285 BUSHING
5734 HOUSING
18081 PIN 1786 O-RING
1918 SPRING 2477 VALVE 1945 PLUG
APT 3-8
rev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
AMERICAN PNEUMATIC TOOL
MODEL 133 4-BOLT HANDLE RIVET BUSTER
The APT Model 133 4-Bolt Handle Rivet Buster is another variation of the “classic” Model 133 Rivet Buster. The Model 133 4-Bolt Handle features a 4-bolt style handle which incorporates a vibration dampening feature as well as a flapper style valve. The Jumbo Rivet Busters, as they are known, were originally designed to cut rivets off metal structures. The APT Rivet Buster Series are now widely known now as tough, powerful tools, with the ability to perform medium to heavy demolition work. At half the weight of the 60 lb. class paving breakers, the ratio of its high impact energy versus its weight makes the Rivet Buster Series the most efficient tools APT makes. The Model 133 4-Bolt Handle meets the weight requirements for bridge deck repair work. Rivet Busters are also popular for cutting up underground tanks.
SPECIFICATIONS Part Number
Bore
17736
1-3/16
Stroke
BPM
CFM @ 90 PSI
Weight
Length
lbs.
inches
Air Inlet NPT
28
24-1/4
1/2 Female
inlet pressure
8
1000
36-40
FEATURES 8" stroke Inside trigger for better control and safety ■ Flapper valve ■ Handle design has a vibration dampening feature ■ Deep case-hardened alloy steel cylinder ■ Uses jumbo extra heavy duty tool steel ■ Heavy duty upper and lower sleeves ■ Adjustable exhaust deflector ■ ■
APT
rev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
3-9
AMERICAN PNEUMATIC TOOL
18148 HANDLE ASSY (SEE DETAIL BELOW)
APT MODEL
16531 (4) BOLT
133 4-BOLT 4-BOLT RIVET BUSTER
1532 (4) LOCK WASHER
PART #17736
17738 SNUBBER 5739 (4) WASHER
17737 COLLAR
1318 VALVE 767 PIN 767 PIN
3165 PISTON
8825 VALVE 17745 VALVE
17742 CYLINDER
17744 EXHAUST DEFLECTOR
4374 SLEEVE 2994 SPRING
210 LEVER
3171 RETAINER
17741* HANDLE
4364 PIN
18148 HANDLE ASSY
3170 BUMPER
5734 HOUSING 1782 THROTTLE VALVE ASSY
1786 O-RING 17985 HANDLE SUB ASSY
2477 VALVE
1175555 SPRING
17986 INSERT 17114 BUSHING
2074 O-RING 17988 BUSHING ASSY
*FOR REFERENCE ONLY (THESE PARTS NOT SOLD SEPARATELY)
17987 AIR INLET BUSHING
1783 BUSHING
17085 PIN
APT 3 - 10
rev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
AMERICAN PNEUMATIC TOOL
MODEL 133-T 1133-T RIVET BUSTER
The APT Model 133/1133 T-Handle Rivet Buster has been designed with an extended T-style handle ideal for vertical demolition work. The APT Rivet Buster is widely known as a tough, powerful tool, with the ability to perform medium to heavy demolition work. At half the weight of the 60 lb. class Paving Breakers, the ratio of its high impact energy versus its weight makes the Rivet Buster series the most efficient tools APT makes.
SPECIFICATIONS Part Number
Bore
Stroke
BPM
17070
1-3/16
8
1140
17552
1-3/16
11
850
CFM @ 90 PSI
Weight
Length
lbs.
inches
Air Inlet NPT
42-46
35
31
1/2 Female
48-52
38
34
1/2 Female
inlet pressure
FEATURES 8" or 11" stroke Drop forged T-style handle ■ Rubber hand grips ■ Deep case-hardened alloy steel cylinder ■ Uses jumbo extra heavy duty tool steel ■ Heavy duty upper and lower sleeves ■ Adjustable exhaust deflector ■ ■
APT
rev 1/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656
3 - 11
AMERICAN PNEUMATIC TOOL APT MODEL 133-T/1133-T
17133 HANDLE
RIVET BUSTER 133-T PART NO. 17070 (8" STROKE) 1133-T PART NO. 17552 (11" STROKE)
3161 SPRING
3160 VALVE ASSY
3156 REAR VALVE
3157 VALVE
16592 PIN
3158 FRONT VALVE
3165 (8") 17529 (11") PISTON
3152 (8") 17398 (11") CYLINDER
2994 SPRING
3162 RING 3163 DEFLECTOR
3253 GRIP
4374 SLEEVE 1819 LEVER
17067 HANDLE ASSY
3171 RETAINER
17133 HANDLE
3170 BUMPER
105 PIN
5734 HOUSING
112 FELT 111 PLUG
1821 SPRING 3386 BUSHING ASSY
17067 Handle Assy includes: 111 plug (1), 112 felt (1), 212 bushing (1), 5634 handle (1).
212 BUSHING
209 PLUG
*3384 BUSHING 3385 SCREEN
3360 VALVE ASSY
3253 GRIP
1786 O-RING
3359 RING 3358 SEAL 3357 VALVE
APT 3 - 12
rev 3/99
14710 MAPLE AVENUE • GARDENA, CA 90248 • (310) 538-2600 • FAX (310) 323-6656