Data Loading...
UL Listed Digital Cellular Communication for Fire Alarm ... Flipbook PDF
FDNY Search dmpalarms UL Listed . Digital Cellular Communication for Fire Alarm Control Panels. GSM/GPRS DIGITAL CELLULA
115 Views
65 Downloads
FLIP PDF 501.84KB
Search dmpalarms
FDNY
UL Listed Digital Cellular Communication for Fire Alarm Control Panels The 463G, when installed in a DMP XR500/ XR500FC Panels, is UL approved as a primary (standalone) fire communicator with no backup, or as a fire slave communicator, that is compatible with any FACP. The 463G provides a dependable communications link between your alarm system panel and Central Station. • Compared to a dialup communication link, cellular can save significantly in annual telecom costs • UL Listed as the Primary Communicator and Fire Slave Input for the XR500 in Fire Applications under ANSI/UL 864 Commercial Fire (Meets NFPA 72) • Works on digital cellular GPRS data networks over a variety of carriers, including AT&T (USA) and Rogers (Canada)
GSM/GPRS DIGITAL CELLULAR FIRE COMMUNICATOR 463G FEATURES • 463G enhances system security that conforms with NFPA and UL requirements • Direct reporting to the DMP Central Station receiver, with no relaying of alarm signals • Fire Slave Input option of the XR500 with 463G approved for any FACP • Modular solution means easily updated for newer technologies • Eight-path redundancy with multiple message delivery available • DMP Adaptive Technology™ switches communication paths while maintaining supervision if the current path becomes unavailable
• 463G uses power from panel with low current draw for long standby battery life • Can be equipped with local or remote antenna, offering more flexibility when installing • Cellular data throttling offers overage suppression • Ability to check signal strength indication at the keypad • Messaging features transmit alarms/alerts to users via SMS text messages, and allow users to remotely control their panel via text commands
Intrusion | Fire | Access | Network | Cellular
UL LISTED Install the DMP 463G Digital Cellular Communicator in an XR500 Series panel to create a UL listed, primary communication path for commercial fire installations. The Fire Slave Input option of the XR500 has also been approved under ANSI/UL 864 (NFPA 72 2007 & 2010), allowing it to be used as a Slave Communicator for any FACP.
DIRECT REPORTING The digital cellular communicators transmit IP data packets directly from the panel’s processor over the GSM/ GPRS wireless data network. All of the messages that are capable of being sent by the control panel are received directly by the DMP Central Station receiver. There are no intermediary servers or network operation centers, and no retransmission or reinterpretation of the information. Direct reporting means faster response, with no concerns about signals not being properly relayed or intermediate communication links failing.
ADD-ON TO XR500 PANEL The 463G works as an easy-to-install XR500 expansion card, with plugand-play ease of installation. No extra programming is required. It provides full data delivery of DMP Zones, Areas, and Users, with all names and details included. Th e re m a r k a b l y c o m p a c t 4 6 3 G won’t take up a lot of space in your communications closet. The unit directly installs in the XR500 expansion card slot, which is mounted inside a sturdy ULlisted metal cabinet. Tamper protection is also available for added security.
FULLY SUPERVISED You’re kept fully informed of system status. The unit sends full reporting messages including Zones, Areas, and Users, with all names and details included. Full supervision ensures that the cellular communication path is intact and functional.
EIGHT-PATH REDUNDANCY Feel more secure with up to eight paths of communication redundancy. Select from TCP, UDP, RS232, GPRS, Single Line Dialer, Dual Line Dialer with multiple IP numbers, and multiple telephone numbers. You identify and configure your redundant communication links via Remote Link. A DACT (digital alarm communicator transmitter) system may be configured as: • Path 1 Type DD Primary and Path 2 Type DD Backup • Path 1 Type DD Primary and Path 2 Type CELL Backup • Path 1 Type DD Primary and Path 2 Type NET Backup
A NET or CELL system may be configured as: • Path 1 Type NET Primary with no Backup • Path 1 Type CELL Primary with no Backup • Path 1 Type NET Primary and Path 2 Type DD Backup • Path 1 Type NET Primary and Path 2 Type CELL Backup • Path 1 Type CELL Primary and Path 2 Type NET Backup
ADAPTIVE TECHNOLOGY™ If the primary communication path is compromised or becomes unavailable, Adaptive Technology almost instantly switches to a designated backup path. Where multiple backups are available, communications can be programmed to switch to another path as necessary. The checkin frequency and programming for a backup path adapt to the checkin programming of the primary path. When the primary path becomes available, normal communications are restored. Adaptive Technology provides additional confidence in the integrity of your system, while protecting you from unexpected cellular service charges.
REDUCED EQUIPMENT NEEDS With other cellular backup equipment, you need to purchase additional enclosures, power supplies, batteries, cabling, and conduit connections. The 463G reduces the number of pieces of equipment you have to purchase. It comes ready to mount, reducing your initial costs and simplifying both installation and ongoing operation.
REDUCED COMMUNICATION COSTS Adding the cellular communicator to the DMP XR500 fire alarm control panel can lower costs significantly compared to dial-up connections. Fire systems typically require two dial-up lines that can be eliminated and replaced with a single cellular connection.
ANTENNA PLACEMENT The unit includes both local and remote SMA (S-band multiple access) antenna connections, giving you added freedom and flexibility during installation.
LOW CURRENT DRAIN With its extremely low current drain and long standby battery life, the 463G will continue to provide a communications link for an extended period of time, even during a power failure. It draws half the current of other comparable units.
SPEC SHEET SIMPLE TO INSTALL AND PROGRAM Connect the 463G to your panel, attach the antenna and power, and installation is complete. Programming the 463G is fast and simple, accomplished within the panel itself. After programming the 463G cellular communications path via Remote Link, you will be presented with the Activate SIM window to activate your cellular plan. Once activated, the wireless backup connection is immediately online protecting your communications link. No separate programming utility is required.
SECURECOM CELLULAR SERVICES The 463G comes standard with a SIM (Subscriber Identity Module) card ready to use SecureCom Wireless Cellular Service from DMP. With the 463G and SecureCom, you have a one-stop resource for both hardware and cellular service.
ENHANCED FIRE PROTECTION Compared to dial-up connections, a digital cellular communication link provides greater reliability, protection from sabotage, and is less prone to being knocked out by weather. Unlike mobile cellular connections, the 463G creates a fixed network connection that minimizes hand-offs and the chance for dropped connections. When trouble conditions occur, they can be more quickly diagnosed and often corrected remotely. The NFPA 72 code requires a test of the entire communications path every five minutes. The DMP Model XR500 Command Processor Panel used with DMP 463G Digital Cellular Communicator meets this requirement when check-in and fail time settings are programmed for five minutes. The net result is a higher level of system reliability in comparison with traditional systems that rely on redundant phone lines and the substantially less frequent 24-hour supervision reports associated with that approach.
UPDATEABLE
MESSAGING FEATURES
In addition to being able to change cellular carriers, you will also be ready to take advantage of technical improvements as they occur. The unit’s modular architecture enables seamless upgrades as improved technology becomes available.
CELLULAR DATA THROTTLING D M P p a n e l s p ro t e c t y o u f r o m unexpectedly high cell phone charges for usage over the plan limits with overage suppression. When cell data traffic exceeds 3K/hour, you receive an hourly alert advising you of the high traffic. When traffic exceeds 6K/hour, the panel will begin to automatically suppress non-alarm messages, including check-ins. When cell traffic drops back below the 3K/hour limit, full communications are automatically restored.
Including cellular communication in the panel enables the Messaging Features that make it possible for users to remotely interact with their panel. The panel can be programmed to transmit email*/SMS messages to as many as three addresses, including cell phones or email addresses (up to 48 characters each). End users can receive email or text messages each time there’s a system event such as arming and disarming, zone bypass, or any alarms. Messaging can be configured via Remote Link™ or from the keypad. Full panel programming can be done over cellular. Users also have the ability to send commands via text messages to the panel. They can arm or disarm their system, control outputs, retrieve system status, and perform other functions. Each command received by the panel is acknowledged back to the user via return SMS Message. Dealers have the opportunity to generate additional recurring revenue by offering these features to customers. *For email messages, network or cellular communication must be present.
Use any model of cell phone for Messaging Features
Intrusion | Fire | Access | Network | Cellular
Digital Cellular Communicator DMP WIRELESS DEVICES FOR ANSI/UL 864 COMMERCIAL FIRE Complete your fire system with other DMP wireless devices that are ANSI/UL 864 Listed for Fire Protective Signaling Systems.
TWO-WAY COMMUNICATION Superior to traditional wireless devices that just broadcast until the zone is restored, DMP 1100 Series require an acknowledgement from the 1100 Series Receiver, indicating successful communication. This smart technology ensures that each and every communication is received and efficiently processed at the panel. With the 900MHz frequency-hopping spread-spectrum technology, clear and accurate signal transmissions without interference in practically any environment is to be expected.
1103 UNIVERSAL TRANSMITTER
1181 POST INDICATOR VALVE The model 1181 PIV is a weather proof and tamper resistant wireless switch for monitoring the open position of fire sprinkler control values of the post indicator, butterfly and other types.
Model 1103 Universal Transmitter is typically used in commercial fire or burglary door/ window applications. It offers the same look and features as the 1101 transmitter, with the addition of a 470k end-of-line resistor and wall tamper switch.
1182 OS&Y
1100 SERIES RECEIVERS The 1100 Series Receivers: 1165/1165H/1165HS 1100X, 1100XH and 1100R COMMERCIAL SMOKE allow you to add up to DETECTORS 500 transmitters and is The Model 1165 required for wireless S m o k e D e t e c t o r, capability in both 1165H Smoke/Heat re g u l a r a n d h a r s h Detector, and 1165HS environments. Smoke/ Heat Detector with Sounder include a tamper switch that sends a trouble signal if the detector is removed from the mounting base.
Primary Power Current Draw Standby Alarm
ACCESSORIES CONT. 12 VDC from panel 22 mA 45 mA
COMPATIBILITY DMP Command Processor panels XR500, XR500N, XR500E using Software Version 202 or higher
ORDERING INFORMATION 463G Cellular Communicator
ACCESSORIES 380-400 381-12 381-25
Replacement Level 400 SIM Card 12' Coax Extension 25' Coax Extension
quality. integrity. innovation.
383 386 387-1 387-2 387-3 387-25 387-50
Rubber Duck Antenna Wall Mount Antenna Bracket 3dB Fiberglass Antenna w/bracket 2dB Attack Enclosure Antenna 3dB MEG Antenna SMA TO N CABLE, 25FT, LMR195 SMA TO N CABLE, 50FT, LMR195
LISTINGS AND APPROVALS California State Fire Marshal (CSFM) FCC ID: MIVGSM0308 Industry Canada ID: 4160A-GSM0308 New York City (FDNY COA #6055) Underwriters Laboratories (UL) Listed ANSI/UL 365 Police Station Connect Burglar Alarm Systems ANSI/UL 985 Household Fire Warning System Units ANSI/UL 1023 Household Burglar Alarm System Units ANSI/UL 1076 Proprietary Burglar Alarm Units & Systems ANSI/UL 1610 Central Station Burglar Alarm Units ANSI/UL 864 Control Units for Fire-Protective Signaling Systems
Intrusion | Fire | Access | Network | Cellular
2500 North Partnership Boulevard Springfield, Missouri 65803-8877
800.641.4282 | dmp.com Made in the USA
© 2011 Digital Monitoring Products, Inc. | LT-1165 | 10/11
SPECIFICATIONS
The 1182 OS&Y Switch is used to monitor the open position of an OS&Y (Outside Screw and Yoke) type gate valve. The 1182 mounts conveniently to most OS&Y valves ranging in size from ½” to 12”. The switch operates the external contacts of the wireless transmitter when the valve position is altered from an open state.